Vidikron VP-6000a, VP-4200a, VP-5000a manual 1Table of Contents

Page 7

	1Table of Contents
THREE YEAR LIMITED WARRANTY		iii
Safety Precautions		vi
1.	Introduction	1
	About This Manual	1
	Target Audience	1
	If You Have Comments About This Manual	1
	Textual and Graphic Conventions	1
	Using This Manual	2
	Description, Features and Benefits	3
	Key Features and Benefits	3
	Parts List	4
2.	Controls and Functions	5
	PlasmaView at a Glance	5
	Controls and Indicators	5
	Connectors	7
	PlasmaView Remote Control	10
3.	Installation	13
	Remote Control	13
	Notes on Batteries	13
	Notes on Remote Control Operation	13
	Quick Setup	15
	Installation Considerations	16
	High-Altitude Operation	16
	Mounting the PlasmaView on a Wall or Table Stand	16
	Ambient Light	17
	Ventilation	17
	Other Considerations	18
	Connections to the PlasmaView	19
	Video Connections	19
	Audio Connections	23
	RS-232 Controller Connection	25

Vidikron PlasmaView Owner’s Operating Manual

vii

Image 7

Contents

High Definition Plasma Displays Page Three Year Limited Warranty RIGHTS, Limits and Exclusions Vidikron DOC Compliance Notice Safety Precautions1Table of Contents Serial Communications Maintenance and TroubleshootingSpecifications Operation1List of Figures Audio Output Connection Connecting SpeakersList of Figures About This Manual 1IntroductionPerformance or cause a malfunction Using This ManualInformation about obtaining service They also provide supplemental informationKey Features and Benefits Description, Features and BenefitsIntroduction 2Controls and Functions Controls and IndicatorsPlasmaView at a Glance INPUT/UP Handles at the rear of the panelLeft / VOL and Right / VOL + PlasmaView Model VP-4200 Connector Panel PlasmaView Model VP-5000 Connector Panel Analog RGB OUT Input 1 15-pin D-Sub Audio Output 3.5-mm stereo mini jackAudio Input 1 3.5-mm stereo mini jack Audio Input 2 3.5-mm stereo mini jackPlasmaView Remote Control PlasmaView Remote ControlOFF pin hole Installer Adjust pin holeVolume + Directional ButtonsControls and Functions Approx 23 ft 7m 3InstallationRemote Control OperationInstallation Through Quick SetupStep Procedure For Details, refer to Display propertiesHigh-Altitude Operation Installation ConsiderationsVentilation Requirements for Enclosure Mounting VentilationInstallation RGB/Component Video Input 1 Connection Connections to the PlasmaViewAnalog RGB OUT Input 1 Connection Composite or S-Video Input 3 Connection Component Video Input 4 Connection Attaching the Small Ferrite Cores to Audio Cables 11. Audio Output Connection 13. RS-232 Control System Connection ConnectionInstallation 4Operation Turning on the PowerChanging the OSD Language Setting the Computer Display Properties Selecting an Input Source Viewing Input Signal InformationChanging the Aspect Ratio Description PIX by PIX Using the On-Screen Menus Option PictureScreen Set-UpMain Menu Picture Perform the adjustments in the order listed hereTypical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness To highlight Image Position ScreenSet-Up PowerPower Turning the picture IndicatorDVI Setup Option Language Refer to Changing the OSD Language onType 3 causes the image to move one pixel at a time PlasmaView, Auto Function becomes active again Option Installer Adjust ModeFAN Speed Auto ISF CCC color mode is pre-set to approximately 3,200K This action is not undoable. Proceed with caution Picture OrientationTo use PIP, press the Split button Using Picture-In-Picture PIPWindows Sub-screen or vice versa. This switches the audioPress the Swap button to replace the main screen with Viewing an Enlarged Area of the Display Enlarging One Part of the ScreenOperation Cleaning the Screen 5Maintenance and TroubleshootingCleaning Troubleshooting TipsFAN Failure OUT of Range Signal NGThermal Alert Shut Down6Serial Communications Serial Command SyntaxArgument 3 bytes Minimum Command Value Range DescriptionMSTS02 Minimum MaximumVideo AudioMSTS09 MSTS08MSTS10 Functional Lock SET-UP Menu CommandsVideo Average Option Menu CommandsPicture Menu Commands Installer Adjust Mode SET-UP Menu Commands Installer Adjust Mode Screen Menu Commands Installer Adjust ModeOption Menu Commands Installer Adjust Mode Contrast MonotoneInput 1... Input DW1 Minimum Maximum Adjustment Commands7Specifications End user except for plasma glass panel Specifications are subject to change without noticeDelivery to the end user PlasmaView Dimensions 25.00 14.00 48.41 49.98 13.98 Specifications Input Refresh Rate Computer/Video Signal CompatibilityHoriz 1152x870 Specifications Page RUMA-009815 Rev -07-07