PYLE Audio PLDVD170 operating instructions Connecting, Refer to

Page 13

Connecting

AMP Select

Press AMP SEL button on the remote repeatedly, select the amplifier mode you need ( depending on the connection mode).

Press

AMP SEL to select the mode you need

Connection mode

AMP mode

 

 

 

 

Display on pannel

Using the speaker cables

I

AP

On

Connecting PURPLE with white

 

 

 

stripe cable to the Remote eye

E

AP

On

jack on the rear of Amplifier,

or using the Audio / coaxial cable

 

 

 

Connecting the Audio cable to

 

 

 

the monitor or audio system

A

AP

OFF

(refer to page 9)

Any connection mode

A

AP

On

 

 

 

 

Note: Setting to ALL, the player will be in high consumption.

So we advise to select the right mode for your connection mode.

Note on Connecting

NOTE 1

1)THE DVD PLAYER USES 12V DC AND THE COVER IS GROUNDED. 2)THE DVD PLAYER HAS A HIGH-POWER 4 CHANNEL BUILT IN AMPLIFIER.

THE SPEAKER CABLES USED MUST BE A MINIMUM OF 18 GAUGE CABLE, IF ONLY CONNECTING 2 SPEAKERS, YOU MUST CONNECT THE 2 FRONT SPEAKERS (FL, FR) OR 2 REAR SPEAKERS (RL, RR).

3)THE UNUSED SPEAKER CABLES MUST BE PROPERLY INSULATED WITH TAPE OR TERMINATING CONNECTORS TO AVOID A SHORT.

NOTE 2

1 Refer to the owner's manual for " the connected monitor " as well.

2 Connect the DVD video player to your monitor directly. If you connect the DVD player to a VTR, TV/VTR combination or video selector, the playback picture may be distorted as DVD discs are copy protected.(refer to " NOTE ON LOCATING" )

NOTE 3

1 Refer to the owner's manual of the connected equipment for additional information.

2 When you connect the DVD player to other equipment, be sure to turn off the power .

3 If you place the DVD near a tuner or radio, the radio broadcast sound might be distorted. In this case, place the DVD player away from any other tuner or radio.

4 The output sound of the DVD player has a wide dynamic range. Be sure to adjust the receiver's volume to a moderate listening level. Otherwise, the speakers may be damaged by a sudden high output.

5 Turn off the amplifier before you connect or disconnect the DVD player's power leads. If you leave the amplifier power on, the speakers may be damaged.

10

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Model PLDVD170 System Functions FeaturesTable of Contents Safety Precautions Important Instructions To obtain a clear picture PrecautionsIdentification of controls Skip button DVD play modeOther indicators Indicators vary depending on the kinds of discs you playDVD display Remote control operation Full direction Remote controlPreparing the remote control When using remote controlOperating with the remote control Connections Outlet wires connection suppliedAntenna jack Connecting to a monitor and speakers , or audio systemRefer to ConnectingBasic playback Playing a discTo start playback from the menu screen To power on/off the playerTo pause playback To stop playbackPlaying at various speeds Resuming playback from the same location Advanced playbackPlaying from the desired location Locating a specific title, chapter, or track Press MENU, in PBC on modePlay Mode Playing without sound Playing repeatedlyRepeating a title, chapter, or track Selecting sound For DVD Discs Selecting a playback audio settingSelecting subtitles Selecting the camera angleUsing the on-screen display Function setupChecking the operational status Language Video Audio Rating Customizing the function settingsPCM MP3 Instruction Radio operation Radio tuningAdjusting the volume Auto Travel Preset operationDVD player mode Button Press the button on the remote On the remoteOthers How to deal with discs Theres no sound TroubleshootingTheres no picture Do not playSpecifications Installation Accessories and HardwareSet Removal Two black sticking papers
Top Page Image Contents