Esoteric D00864200A manual Link Audio Output Setting, 60958, Pcm, Off, Flow Status

Page 42

i.LINK (AUDIO) Output Setting

When the i.LINK (AUDIO) terminal is connected to an amplifier or a D/A converter, select proper i.LINK output setting.

When playback is stopped, hold down the STOP button for more than 2 seconds and release it when “i.60958”, “i.PCM” or “i.OFF” appears on the display.

Each time the STOP button is pressed for 2 seconds, the output setting changes.

When using the i.LINK terminal, select “i.60958” or “i.PCM”, and set the Digital Output setting to “ON”.

i.60958

When the disc is DVD-video/VCD/CD, the digital signal is output in the format (Stream or PCM) you set in the Audio Digital Out (see page 37).

<DSD signal is output during playback of a SACD disc, and linear PCM digital signal during playback of a DVD-Audio disc.

i.PCM

Linear PCM digital signal is output when the disc is DVD- video/VCD/CD.

Dolby Digital/DTS/MPEG signals are converted into linear PCM.

When the i.LINK (AUDIO) terminal is connected a component without a Dolby Digital/DTS/MPEG decoder, select “i.PCM”.

<Some amplifiers may regard this signal as DVD-Audio.

<DSD signal is output during playback of a SACD disc, and linear PCM digital signal during playback of a DVD-Audio disc.

i.OFF

Select this when you don’t use the i.LINK (AUDIO) terminal. No signal is output from the i.LINK (AUDIO) terminal.

<There is no difference between i.60958 and i.PCM as far as SACD or DVD-Audio disc playback is concerned.

<Set the Analog Out setting to “Multi channel” to output the surround sound from a DVD-Audio and SACD disc.

When the Analog Out setting is set to “2ch”, the multi- channel sound is downmixed to 2 channels.

<In case you experience any problem with the audio output, read the instructions of the connected component to check the adaptable format.

If the connected component cannot accept 4% down signal, set the 4% down mode off.

Flow Status

While the display shows “i.60958” or “i.PCM”, repeatedly press the STOP button to turn ON or OFF the flow status.

If the component connected via the i.LINK terminal is compatible with the flow rate control, and if you set the flow status of the UX-3 ON, the connected component will work in the flow rate control mode.

<Though the flow status function of the UX-3 is not same as the flow rate control, RAM buffer of the connected component will absorb clock differences and control the flow rate using the clock of the connected component.

<In the following cases, set the flow status OFF:

•The connected component isn’t compatible with the flow rate control.

•Though the connected component is compatible with the flow rate control, the flow rate control doesn’t work properly with this unit.

•Sound skips.

<During playback of a video source, the flow status is automatically set to OFF to keep the synchronization of audio and video.

<When the flow status is set to ON, “i.60958 FL” or “i.PCM FLOW” will appear on the display instead of “i.60958” or “i.PCM”.

42

Page 41 Page 43
Image 42
Page 41 Page 43
Contents DVD/DVD-A/SACD/CD Player Important Safety Instructions For U.S.A Contents Features What’s in the box Placement of the unitBefore Use Conventions about This ManualRestoring factory settings Changing the Color System NTSC/PALAbout MOD.Modulation PAL Discs Type of Discs That Can be Played on This SystemSacd Following discs cannot be played with this unit Example of Icons used on DVD discsConnection to a TV TV MonitorComponent video output terminals DVI-D video output terminalD1/D2 video output terminals component Video output terminalConnections to an amplifier, etc Power cord receptacle Word sync connectorSignal GND connection Analog audio output terminalsFront panel features Front panel display Understanding the remote control unit How to insert the batteries Playback On-screen menuStopping playback Pausing playback freezing the pictureResume mode Opening and closing the traySelecting a chapter or track Selecting groups and titlesSkipping playback Selecting the playback areaChapter and track repeat Repeat modeFast scanning Title, group, disc repeatWhen selecting tracks from a DVD audio disc Programmed playbackFinish the programming by pressing Play Adding tracks to the list Changing camera angleClearing the last track from the list Clearing the whole programSlow motion Slow motion/frame advanceSelecting audio Frame advanceLip sync Use the FL Dimmer button to cycle between these settingsSelecting subtitles Display dimmingDVI level DVI outputDVI output format DVI output aspect ratioTurning video on and off Clock ModeDown mode Analog sound output 2CH/MULTIDVD video playback on-screen display Changing the display modeDVD video playback main unit display DVD video stopped, on-screen displaySACD/CD/video CD playback main unit display DVD audio playback on-screen displayDVD audio stopped, on-screen display SACD/CD/video CD stopped, main unit displayUse the cursor buttons to navigate the menus Settings introductionExit the setup mode by pressing Setup once more Enter the menu item with the right cursor buttonDigital output settings Settings AudioAnalog output settings CD Digital DirectGroup playback mode DVD audio Audio DRC Dynamic Range ControllingDownmix Progressive scan setting Settings VideoVideo adjustment EnterSubtitle language selection Settings LanguageAudio language selection Displaying subtitlesLanguage Code List Language CodeSpeaker distance Settings General/Speaker setupSpeaker Size Speaker levelsSettings General Test tone lengthDigital output formats Settings General/Video Out TV screenVideo output PAL-NTSC conversion Still modeComponent video output Closed captioningSettings General/Display Parental ControlCountry Code Setting the level of controlResetting the password Playing a controlled discPCM Link Audio Output Setting60958 OFFCopyright protection system Dtcp How to connect multiple i.LINK-capable devicesLink Ieee Data transfer rateTroubleshooting Maintenance Beware of condensationSpecifications Block Diagram SacdTeac Esoteric Company
Top Page Image Contents