Timer Recording, Station names | Daewoo SD-3500, SD-9500 guide

Tuning in New Stations

Station names

Timer Recording

■For timer recordings, clock, date, and stations must be set correctly.

■Load a cassette with its safety tab in place and with sufficient free space for the recording.

■If your player is showing no station name or is showing a station name incorrectly, you can correct this.

1	Call this menu (just see the previous page),	MANUAL SET
	if it isn't displayed.	PR	01
		RECEPTION	AERIAL
		AUTOSEARCH	CH01
	Select NAME position.	FINE TUNING
		DECODER	ON
	Press the [0] button to change the given name.	NAME	_ _ _ _
		PR+/-: UP/DOWN
	Or press the [1] button to create the station name.	0/1: CHANGE/CREATE
		OK:CONFIRM	SETUP:END

Timer recording using ShowView (SD-9500 only)

	Call the ShowView menu by pressing PROGRAM on the
1	remote control.
	From your TV magazine, type in the number next to the
	programme you want to record ...
	... and confirm.

SHOWVIEW

83077----

0-9:SHOWVIEW NUMBER < :CORRECT

OK:CONFIRM SETUP:END

Either select the name from the stored list or you

2 create the station name and enter a 4-digit name. Change the letters with the [PR +/–] buttons, move to the next letter with the [< / >] buttons.

3	Store and exit.

MANUAL SET

PR	01
RECEPTION	AERIAL
AUTOSEARCH	CH_ _
FINE TUNING
DECODER	ON
NAME	O_ _ _

PR+/-: SELECT CHARACTER

</>: SELECT POSITION

OK:CONFIRM SETUP:END

MANUAL SET

PR01 ARD	PR08 P-08
PR02 ZDF	PR09 P-09
PR03 P-03	PR10 P-10
PR04 P-04	PR11 P-11
PR05 MTV	PR12 ----
PR06 P-06	PR13 ----
PR07 P-07	PR14 ----

PR+/-:SELECT

OK:CONFIRM SETUP:END

	Decide if you want to record "ONCE", "WEEKLY" or "DAILY"...
2	... and confirm.

	If you wish to make changes:
3	Move to the position you want to change using the [< / >]
3	Changebuttons. the setting using the [< / >] or [number] buttons. If all

setting are ok, press [ok], till you see “OK: CONFIRM” in the bottom line.

HOW OFTEN DO YOU WANT TO RECORD THIS PROGRAM?

ONCE WEEKLY(ONCE A WEEK) DAILY(MON-FRI) DAILY(MON-SAT) DAILY(MON-SUN)

PR+/-:SELECT

OK:CONFIRM SETUP:END

TIMER PROGRAM (ONCE)

PR	03
START TIME	21:20
END TIME	22:20
START DATE	14/10(SAT)
TAPE SPEED	SP
VPS/PDC	ON
PR+/-:SELECT (AV1/AV2)
0-9 : SETUP (PR)
</>:CORRECT
OK:CONFIRM	SETUP:END

VCR Operation

Sorting programme locations

If the location numbers used for programmes stored in your TV and player are different, you can change them on the player. To do this, move the stations to the right numbers, until they are arranged the way you want.

Confirm.

Switch your player off.

Call the player’s "MAIN SETUP", choose "PR PRESET" then "PR ALIGN".

Select the programme to swap.

Confirm by pressing OK button.

Move the station to the desired location number. Confirm by pressing OK button.

PR ALIGN

PR01ARD	PR08 P-08
PR02 ZDF	PR09 P-09
PR03 P-03	PR10 P-10
PR04 P-04	PR11 P-11
PR05 MTV	PR12 ----
PR06 P-06	PR13 ----
PR07 P-07	PR14 ----

PR+/-:ALIGN

<:PR VIEW

OK:CONFIRM SETUP:END

•	VPS/PDC is a service provided by some stations to enable you to perform timer recordings
	precisely even if the broadcaster delays the start time of the programme slightly. The time you
	enter is the VPS/PDC time so must be correct. Not all stations offer VPS/PDC, in which case the
	player will start at the time you enter and not the actual start time of the programme.
	If you wish to start recording at a specific time without it being adjusted by the VPS/PDC
	system in the event of a delay, switch VPS/PDC off otherwise the player will not record.
•	If you don’t have the ShowView numbers see next page for the normal timer.
•	If you have made a mistake, move back to the relevant position with the [<] button and change
	the setting.

Clearing programme locations

1 Call the player’s "MAIN SETUP", choose "PR PRESET" then "PR ERASE".

2 Select the station (location number) you want to clear.

Review the picture by pressing [<] button.

Clear by pressing OK button.

PR ERASE

PR01 ARD	PR08 P-08
PR02 ZDF	PR09 P-09
PR03 P-03	PR10 P-10
PR04 P-04	PR11 P-11
PR05 MTV	PR12 ----
PR06 P-06	PR13 ----
PR07 P-07	PR14 ----

PR+/-:SELECT

<:PR VIEW

OK:ERASE SETUP:END

•	If there is no programme location displayed under “PR” in the change menu, the player doesn’t
	yet know the location number for the programme you want. Type it in and this will be stored
	for last recordings.
•	If you wish to record from a satellite receiver, select under “PR” the satellite programme
	location or AV (1/2) (depending on the connection with the antenna cable or the SCART-cable).
	Leave the satellite tuner switched on and to the programme you want.
• Should programming overlap, you get a warning.
•	To cancel the recording press the	button (stop) more than 5 seconds.


• ShowView is a trademark applied for by Gemstar Development Corp.. The ShowView system is
	manufactured under license from Gemstar Development Corporation.