Runco 61SBX59B, 53SBX59B manual Rear Panel Jacks

Page 11

REAR PANEL JACKS

STOP

CONNECT ONLY 8 OHM SPEAKERS DO NOT SHORT CIRCUIT

THESE TERMINALS

(Such damage is NOT COVERED by your television warranty)

REAR SPEAKER

RL

ANT A

 

 

 

 

COMPONENT

 

 

S-VIDEO S-VIDEO

Y

CB

CR

TO

 

 

 

S-VIDEO

SUB

CONVERTER

 

 

 

VIDEO

VIDEO

 

WOOFER

 

(MONO)

(MONO)

VIDEO

 

 

 

L

L

L

L

L

 

 

 

 

ANT B

 

 

 

 

 

 

R

R

R

R

R

 

AUDIO

AUDIO

AUDIO

 

 

 

INPUT 1

INPUT 2

MONITOR WIRELESS AUDIO

 

 

 

OUT

OUT

TO HI-FI

Antenna Input/Output

The remote control allows you to switch between two separate 75-Ohm RF antenna inputs, ANT A and ANT B. ANT A input can be displayed as a main picture or sub-picture. ANT B can only be displayed as a main picture. (ANT B cannot be displayed as a sub-picture.) The antenna output labeled TO CONVERTER allows the ANT A connection to pass directly to a different source such as a cable box, when ANT B is displayed as a main picture.

Audio/Video Inputs 1, 2

The INPUT button will step through each video source and antenna source input each time it is pressed. Use the audio and video inputs to connect external devices, such as VCRs, camcorders, laserdisc players, DVD players etc. (If you have mono sound, insert the audio cable into the left channel jack.)

NOTE: You may use VIDEO, S-VIDEO, or COMPONENT: Y-CBCRinputs to connect to Input 2, but note that only one of these may be used at a time.

Monitor Out

These jacks provide fixed audio and video signals which are used for recording. To have S-Video output, S-Video signal needs to be input to input 1 or input 2, or input 3.

Wireless Out

These jacks provide variable audio output to a set of wireless speakers. They can also be used for another stereo system amplifier. With this connection, the audio can be controlled by the television s main volume and also by an independent volume feature found in the THEATER-WIRELESS SOUND menu.

Audio to HI-FI

These jacks provide variable audio output to a separate stereo amplifier. With this connection, the audio to the stereo can be controlled by the television s main volume. Use these jacks for the SURROUND Left and Right channels. (See page 20).

Rear Speaker Terminals

These terminals are used to connect external speakers, which are used for the surround sound feature. The volume level is controlled by the television s main volume and also by an independent rear volume feature found in the THEATER-SURROUND menu. Use speakers with 8-Ohm impedance only.

11

Image 11
Contents 61SBX59B 53SBX59B Power Source Protection and Location of Your Television Safety TipsFor Your Personal Safety For Servicing and Modification Operation of Your TelevisionIf the Television does not Operate Properly Remote Control Battery Installation and Replacement AccessoriesViewing HOW to SET UP Your NEW Hitachi Projection TVAntenna LocationAntenna Connections to Rear Jack Panel HOOK-UP Cables and ConnectorsFront Panel Controls Magic Focus Power lightRemote Control sensor AI Artificial Intelligence sensorFront Panel Jacks and Connections Rear Panel Jacks Sub Woofer First Time USEVideo Inputs 1 Component Y-CBCRInputRear Panel Connections Way signal splitterRear Speaker Terminal Connections Connect After Turning the Power to the TV OFFTips on Rear Panel Connections Tips on Rear Panel ConnectionsExternal Connections Connecting External Audio AmplifierBefore Operating External Video Source Connecting External Video SourcesConnecting a Monaural Audio VCR or Laserdisc Player Connecting a Stereo VCR or Stereo Laserdisc Player Connecting a Stereo Laserdisc Player or DVD Player to Input Audio System Setup Surround Required Optional Effect Feature Connection Light button Genius Remote Control CLU-615MPMULTI-PAGE select switch MULTI-PAGE buttonsSelect MULTI-PAGE WindowsSAT button HOW to USE the Genius Remote to Control Your TVTV button Cable buttonHelp button VOLUME, Mute buttonsPICTURE-IN-PICTURE buttons PIP CH buttonChannel Skip button Exit buttonRecall button MENU, Cursor buttonsPIP button Single Mode PIPSplit Mode PIP PICTURE-IN-PICTURE PIPSplit PICTURE-IN-PICTURE Surf Mode PIPSwap button SingleSplit Freeze Freeze FRZ button With PIP onFreeze FRZ button With PIP OFF Single FreezeExclusive TV buttons Using the Remote to Control VCR FunctionsOperating the precoded function for your VCR Precoded VCR buttonsPrecoded Satellite BOX buttons Using the Remote to Control CABLE/SATELLITE BOX FunctionsPrecoded Cable BOX buttons Precoded AMP, CD, or Tape buttons Using the Remote to Control Audio Equipment FunctionsOperating the precoded function for your audio equipment Amplifier Brand Code AUDIO, CABLE/SATELLITE, and VCR CodesUltratec OSD SET UP Custom Video Audio Theater Info Menu Language SET UPMenu Language Plug & Play Plug & PlaySignal Source Signal SourceAuto Channel SET Auto Channel SETChannel Memory Channel MemoryChannel List Channel ListClock SET Clock SETCenter Mode Static Mode Channel ID Channel List CustomChannel ID Channel IDCAM Video IDVideo ID Video ListFamily Favorites Family Favorites MenuFamily Favorites CH3 Menu Family Favorites OperationParental Control Parental ControlEvent Program Event ProgAuto Link Auto LinkChannel Closed CaptionDisplay ModeFirst Time Tour First Time TourSharpness ResetVideo Contrast Brightness Color TintAuto Color Advanced SettingsColor Temperature Ultra AI Artificial IntelligenceS S AudioBass Treble Balance Internal Speakers MTS ModeAuto Noise Cancel Perfect VolumeTheater Modes TheaterTheater Modes Hall Surround SurroundSurround OFF Matrix SurroundO N T L Dolby PRO LogicGraphic Equalizer Test ToneDolby PRO Logicdolby 3 Stereo PIP Audio Wireless SoundWireless Sound Main TV AudioSUB Woofer Event Reminder InfoSpecial Event Reminder SpecialCalendar CalendarDo not Care of Your Hitachi Projection TV Your Remote Control¥ Ignition Noise Reception ProblemsUseful Info Symptoms61SBX59B InputsOutputs 53SBX59BHome Electronics Division HitachiPage Page QR29802