Runco CX-OPAL42, CX-OPAL47, CX-OPAL55, CX-65HD, CX-55HD, CX-42HD, CX-47HD operation manual Vcr

Page 36

Installation

Component Video Connections: If you have a DVD player, DTV decoder with a component (YPbPr) output or other component video source, connect it to the COMPONENT 1 or COMPONENT 2 input as shown in Figure 3-3.

RGB

COMPONENT 2		COMPONENT 1
L COMP	L	COMP
R 2 Audio	R	1 Audio
S-Video	Video 2/
Video		Video

Video Cable

Audio Cable

DVD/DTV STB

Figure 3-3. Component Video Connections

Composite/S-Video Connections: The Crystal Series LCD has two (2) Composite video inputs and an S-Video input for connecting a VCR, camcorder, laser disc player or DVD player; see Figure 3-4.

If you connect an S-Video source to the Video 2 input, the

Note	Composite input on Video 2 is inactive.

R dio	R	dio
S-Video	Video 2/
Video 2		Video 1
L Video	L	Video
R 2 Audio	R	1 Audio

S-Video Cable

Composite Video Cable

Audio Cable

VCR

Camcorder

Gaming Console

Figure 3-4. Composite and S-Video Connections

22	Crystal Series LCD Installation/Operation Manual

Image 36

Contents Installation / O P E R a T I O N M a N U a L Page RuncoCare Standard Two Year Limited Warranty RuncoCare Standard FeaturesRuncoCare Claim Procedure Page Copyright and Trademarks Important Safety Instructions Compliance Information Declaration of ConformityFCC Part Page Table of Contents ISF Calibration List of Figures List of Figures Xiv Introduction About This ManualUsing This Manual TipDescription, Features and Benefits Key Features and BenefitsOptional Accessories Controls and Indicators Controls and FunctionsCrystal Series LCD at a Glance Handles Status LED Crystal Series LCD Inputs OutputsControls and Functions Model CX-55HD and CX-OPAL55 Inputs and Outputs Model CX-65HD Inputs and Outputs RS-232 Control Port Crystal Series LCD Remote Control Crystal Series LCD Remote ControlRGB HD PIP Controls and Functions Installation Remote ControlBattery Installation Quick Setup Installation OverviewInstallation Considerations Connections to the Crystal Series LCDConnecting the Crystal Series LCD to Source Sections that follow ComponentsAnalog RGB Connections VCR Connecting External Speakers OptionalDigital Audio Connection Connecting an External IR ReceiverRS-232 Controller ConnectionInstallation Turning on the Power OperationChanging the OSD Language Setting the PC Display Properties Using the On-Screen Menus Crystal Series LCD OSD Menu Structure Main Menu SourceAspect Ratio Aspect Ratio Settings Picture Adjust Typical Pluge Pattern for Adjusting Brightness Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Operation Balance Equalizer Speaker Audio Delay Characteristics of the incoming signal SetupLetterbox Mode = Letterbox Hdmi 1 Hdmi 2 Hdmi 3 Hdmi 4 Scart Component RGB Video ISF Calibration Menu should be used by ISF-certified technicians onlyGain Effects of Primary Color Hue Adjustments Crystal Series LCD Splash Screen Using Picture-In-Picture PIP Available Main and PIP Source Combinations Changing the PIP PositionPIP Images Swap button on the remote control Swapping the MainMaintenance and Troubleshooting CleaningTroubleshooting Tips Cleaning the Display Panel Body and Remote ControlMaintenance and Troubleshooting Serial Commands Serial CommunicationsS4E SDE 0001 Personalizing the Splash Screen Using Serial Commands 0090Serial Communications Specifications Crystal Series LCD SpecificationsSpecifications are subject to change without notice Crystal Series LCD Dimensions DimensionsCX-42HD/CX-OPAL42 Dimensions Rear/Side CX-47HD/CX-OPAL47 CX-47HD/CX-OPAL47 Dimensions Rear/Side CX-55HD/CX-OPAL55 Dimensions Rear/Side -8 show the CX-65HD dimensions CX-65HD DimensionsCX-65HD Overall Dimensions Rear/Side Supported Signal Timings by Input Supported TimingsPAL Page 020-0969-01 Rev. a August

Related manuals

Manual 76 pages 11.23 Kb