Sanyo DSR-M manual Precaution, Location, Avoiding Electrical Shock and Fire, Service

Page 2

PRECAUTION

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR OTHER MOISTURE. To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only.

If the power supply cord (AC power cord) of this appliance is damaged, it must be replaced. Return to a SANYO Authorised Service Centre for replacement of the cord.

Location

For safe operation and satisfactory performance of your unit, keep the following in mind when selecting a place for its installation:

Shield it from direct sunlight and keep it away from sources of intense heat.

Avoid dusty or humid places.

Avoid places with insufficient ventilation for proper heat dissipation. Do not block the ventilation holes at the top and bottom of the unit. Do not place the unit on a carpet because this will block the ventilation holes.

Install the unit in a horizontal position only. Avoid locations subject to strong vibrations.

Avoid moving the unit between cold and hot locations. Do not place the unit directly on top of a monitor TV, as this may cause playback or recording problems.

Avoiding Electrical Shock and Fire

Do not handle the power cord with wet hands.

Do not pull on the power cord when disconnecting it from an AC wall outlet. Grasp it by the plug.

If any liquid is spilled on the unit, unplug the power cord immediately and have the unit inspected at a factory- authorised service centre.

Do not place anything directly on top of this unit.

SERVICE

This unit is a precision instruments and if treated with care, will provide years of satisfactory performance. However, in the event of a problem, the owner is advised not to attempt to make repairs or open the cabinet. Servicing should always be referred to your dealer or Sanyo Authorized Service Centre.

CAUTION

Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer.

Discard used batteries according to the manufacture’s instructions.

English

1

Image 2
Contents Page Location PrecautionService Avoiding Electrical Shock and FireFor LAN connection cable/ DVR power cord Power cord Ferrite corePower cord tie Application software IntroductionContents Contents Settings OtherHard disk and cooling fan are consumables Installation conditionsBefore USE Hard disk protection Backup batteryFor important recordings CareNames and Functions of Parts Front panelRear panel Power cord holderALL Reset switch Cord tieBasic connections Installation and ConnectionsConnecting a remote control circuit System controller connectionsConnecting the power cord Connecting cables to the control and alarm terminalsConnecting to a network Changing the position of the operating display Screen Display and PositionOperation display area Example Normal screenTo change the language Setting the LANGUAGE/CLOCKWhen you have made a selection, press Button Press the Menu buttonExample Setting 20 May, 2004, 830 AM Setting the LANGUAGE/CLOCKSetting the time Press the or button to select Press the buttonNormal recording Normal RECORDING/TIMER RecordingTimer recording Set alarm recording Alarm RecordingAlarm recording When alarm input is detectedPlayback Playback while fast-forwarding/rewindingDuring playback, press the Still button Viewing still imagesFrame advance reverse Press the Still buttonSearching for Recorded Images Alarm searchCheck that Alarm Search is Selected, and press the button Image to search Search in Search screenDate/time search Enter the desired alarm numberYou can also search by specifying the desired alarm number Press the or button to select the image to play backPress the button to select View Then press the button Searching for Recorded ImagesPress the button, and set the date/time to search If no image exists for the specified timeCopying image PreviewCD-RW Copying to CF Cards or CD-R/RW Discs and FormattingFormatting a CompactFlash card or Press the and buttons to select Copy START, and then pressSetting the key lock function Releasing the key lock functionDisplaying the menu screen and sub- menu screens Menu Configuration and OperationsTo restore menu setting items to their initial values Press the or button to select the desired menuHDD SET JP.46 Menu Configuration and OperationsOverview of sub-menus Select 1. LANGUAGE/CLOCK SET Press the button Summer Time SET settingsPress the or button to change the setting USE flashes1st DVR 2nd DVR EXT.CLOCK SET settingsWhen USE is selected for Mode under Switch DVR DVR DVR DVR REC Mode SET REC Mode SET setting itemsSelect 2. REC Mode SET, and press Button SettingsStarting recording again when Full indicator lights Press the or button to select YES, then press the buttonSelect 3. Timer REC SET, and press Button Timer REC SETTimer setting items Press the button onceTimer reservations spanning more than 24 hours Timer REC SETTo cancel all timer reservations Press the button to move the cursor to the next itemSetting holidays DISPLAY/BUZZER SET setting items DISPLAY/BUZZER SETDISPLAY/BUZZER SET screen appears Press the and buttons to change the setting, then pressSelect 4. DISPLAY/BUZZER SET, Press the button Setting passwords Password setting examplePassword setting Security Lock SETSetting the user password Security Lock SETCursor to REC Control Admin or UserPress the and buttons to move Lights, and the security lock is setRS-485/NETWORK SET Network connections and settingsSettings for PC or network connection Select 6.RS-485/NETWORK/REMOTE SET and press the buttonRS-485 connections and settings Select 6. RS-485/NETWORK/REMOTE SET, and press the buttonSetting Remote SET Disable flashesDisplays the total amount of disk 1 operation time Power LOSS/USED TimeSelect 7. Power LOSS/USED Time Press the button Select 8. Menu Upload DOWNLOAD, and press the button Menu UPLOAD/DOWNLOADOperations Menu button Button buttonTo save menu items to CompactFlash card „ If Mirroring setting is loadedPress the and buttons to select YES and press the button No flashesFormatting CompactFlash cards To exitSelect 9. HDD SET, and press Button HDD SETInitializing the hard disk Adding a hard disk Setting conditionsHard disk setting screen RS-485 specifications RS-485 termination switch settingsDVR/VCR command table Specifications PALDimensions Unit mm 210 Front 391.5 SideIndex TV System selector switch UP button Timer button Timer indicatorTimer recording Index