Sanyo DSR-M manual Rear panel, Power cord holder, Cord tie, ALL Reset switch

Page 9

2 NAMES AND FUNCTIONS OF PARTS

Rear panel

1	2	3	4	5	6	7	8	INTRODUCTION

	AUDIO		LAN			VIDEO
		OUT		MIC IN		LOOP OUT	OUT

NON REC OUT/

SERIES REC OUT ALARM IN

		CLOCK	SERIES	ALARM RESET
RS485	REMOTE	ADJ	REC IN	ALARM OUT

		TV	RS485							WARNING OUT
		TV	RS485							FULL OUT
		SYSTEM TERMINATE		A	B	C	C	IN OUT	C	FULL OUT
		SYSTEM TERMINATE		A	B	C	C	IN OUT	C
		NTSC	ON
		PAL	OFF
										ALL
										RESET
10	11	9	12					13		14

1.FAN

2.AUDIO IN terminal

3.AUDIO OUT terminal

4.LAN terminal (JP.39)

5.MIC IN terminal

6.VIDEO IN terminal

7.VIDEO LOOP OUT terminal

8.VIDEO OUT terminal

9.TV SYSTEM selector switch

Used to select the video signal between NTSC and PAL systems for the camera input and TV monitor output connected to the digital video recorder.

zTurn the power OFF then ON again after switching the TV SYSTEM selector switch to NTSC or PAL.

10.Power cord holder

Secure the power cord to the holder using the cord tie (accessory) as shown in the illustration.

Cord tie

11.AC INLET

AC power input terminal (3-core)

12.RS-485 TERMINATE switch (JP.48) RS-485 termination ON/OFF switch

13.Control and alarm terminals

	Pin	Signal
	RS-485A	To RS-485 terminal signal A *1
	RS-485B	To RS-485 terminal signal B *1
	C	Common *1
	REMOTE	For wired remote control (VA-RMN01)
	C	Common
	CLOCK ADJ IN	Input for clock setting
	CLOCK ADJ OUT	Output for clock setting
	SERIES REC IN	SERIES-REC input
	NON REC OUT/	NON-REC output/
	SERIES REC OUT	SERIES-REC output *2
	ALARM IN	Alarm input
	ALARM RESET	Alarm reset input
	ALARM OUT	Alarm output
	C	Common
	WARNING OUT	Warning output *3
	FULL OUT	Recording area full warning
*1	Use a twisted-pair cable for connection.
*2	NON REC is output when SERIES REC OUT is OFF.
*3	The following warnings are output:

zHard disk drive error z Fan error z Recording error

zNo input signal when VIDEO LOSS is ON.

14.ALL RESET switch

Resets the clock and backup mode setting.

8

English

Image 9

Contents Page Service PrecautionLocation Avoiding Electrical Shock and FirePower cord tie Application software Power cord Ferrite coreFor LAN connection cable/ DVR power cord IntroductionContents Other Contents SettingsInstallation conditions Before USEHard disk and cooling fan are consumables For important recordings Backup batteryHard disk protection CareFront panel Names and Functions of PartsALL Reset switch Power cord holderRear panel Cord tieConnecting a remote control circuit Installation and ConnectionsBasic connections System controller connectionsConnecting cables to the control and alarm terminals Connecting to a networkConnecting the power cord Operation display area Screen Display and PositionChanging the position of the operating display Example Normal screenWhen you have made a selection, press Button Setting the LANGUAGE/CLOCKTo change the language Press the Menu buttonSetting the time Setting the LANGUAGE/CLOCKExample Setting 20 May, 2004, 830 AM Press the or button to select Press the buttonNormal RECORDING/TIMER Recording Timer recordingNormal recording Alarm recording Alarm RecordingSet alarm recording When alarm input is detectedPlayback while fast-forwarding/rewinding PlaybackFrame advance reverse Viewing still imagesDuring playback, press the Still button Press the Still buttonCheck that Alarm Search is Selected, and press the button Alarm searchSearching for Recorded Images Image to search Search in Search screenYou can also search by specifying the desired alarm number Enter the desired alarm numberDate/time search Press the or button to select the image to play backPress the button, and set the date/time to search Searching for Recorded ImagesPress the button to select View Then press the button If no image exists for the specified timePreview Copying imageFormatting a CompactFlash card or Copying to CF Cards or CD-R/RW Discs and FormattingCD-RW Press the and buttons to select Copy START, and then pressReleasing the key lock function Setting the key lock functionTo restore menu setting items to their initial values Menu Configuration and OperationsDisplaying the menu screen and sub- menu screens Press the or button to select the desired menuMenu Configuration and Operations Overview of sub-menusHDD SET JP.46 Press the or button to change the setting Summer Time SET settingsSelect 1. LANGUAGE/CLOCK SET Press the button USE flashesEXT.CLOCK SET settings When USE is selected for Mode under1st DVR 2nd DVR Switch DVR DVR DVR DVR REC Mode SET setting items REC Mode SETStarting recording again when Full indicator lights SettingsSelect 2. REC Mode SET, and press Button Press the or button to select YES, then press the buttonTimer setting items Timer REC SETSelect 3. Timer REC SET, and press Button Press the button onceTo cancel all timer reservations Timer REC SETTimer reservations spanning more than 24 hours Press the button to move the cursor to the next itemSetting holidays DISPLAY/BUZZER SET DISPLAY/BUZZER SET setting itemsPress the and buttons to change the setting, then press Select 4. DISPLAY/BUZZER SET, Press the buttonDISPLAY/BUZZER SET screen appears Password setting Password setting exampleSetting passwords Security Lock SETSecurity Lock SET Setting the user passwordPress the and buttons to move Admin or UserCursor to REC Control Lights, and the security lock is setSettings for PC or network connection Network connections and settingsRS-485/NETWORK SET Select 6.RS-485/NETWORK/REMOTE SET and press the buttonSelect 6. RS-485/NETWORK/REMOTE SET, and press the button RS-485 connections and settingsDisable flashes Setting Remote SETPower LOSS/USED Time Select 7. Power LOSS/USED Time Press the buttonDisplays the total amount of disk 1 operation time Operations Menu UPLOAD/DOWNLOADSelect 8. Menu Upload DOWNLOAD, and press the button Menu button Button buttonPress the and buttons to select YES and press the button „ If Mirroring setting is loadedTo save menu items to CompactFlash card No flashesTo exit Formatting CompactFlash cardsHDD SET Initializing the hard diskSelect 9. HDD SET, and press Button Setting conditions Hard disk setting screenAdding a hard disk RS-485 termination switch settings RS-485 specificationsDVR/VCR command table PAL SpecificationsUnit mm 210 Front 391.5 Side DimensionsIndex Timer recording Timer button Timer indicatorTV System selector switch UP button Index