GB | INSTALLATION MODE | GB |
Installation Mode
NAddress
Set the address for the LCD monitor (0 ~ 999).
Installation Mode
On program
Tuner Menu
Max Volume
Winter mode
RC inhibition
Child Lock
Address
Baud rate
Panel protection
AV Auto shut off
Network Standby
On Timer Function
LED light setting
DCR
Network initial
Temperature Error
IP Address
Subnet
Gateway
DNS
Select 
Adjust
G2.02 0000
Off
Off
63
Off
Off
Off
0
19200
Off
Off
On
Off
Off
Off
>>>
0
000000000000
000000000000
000000000000
000000000000
MENU Exit
LLSetting the monitor address in RS232 mode
(DFKPRQLWRUFDQKDYHDVSHFL¿F$GGUHVVZKLFKKHOSVFRPPDQG that monitor individually and will not effect to other monitors con- nected to a controlling PC Address format command.
The addressing format command is used for operating multiple monitor sets from a single PC via the RS232C command line.
N Baud rate
Select Baud rate using the or button. To set transmission speed RS232 or
N Panel protection
7RSUHYHQWLPDJHVWLFNLQJZKLFKPD\RFFXUVKRZLQJVWLOOSLFWXUHIRUD long time, select “Panel Protect” using the or button, once highlighted you can select ON or OFF by pressing the or
button.
N AV Auto shut off
This LCD monitor allows you to set up the following:
SETTING PROCEDURE
1.Press and hold the GREEN button on the remote control for 5 seconds. (Installation Mode will appear)
2.Use the or button to highlight each option, use the or button to adjust each option. Press the MENU button to exit the mode.
N On Program
Select ON program using the or button, select the start up position using the or buttons. 2II$95*%$9$93&'9,RU1HWZRUN
N Max Volume
Select Max volume using the or button, use the or buttons to set the maximum volume required.
N Winter mode
This Function can be activated when the LCD monitor is used dur- LQJFROGWHPSHUDWXUHFRQGLWLRQVDSSUR[LPDWHO\Û)Û&RUEHORZWR maintain picture performance.
Using the or button select winter mode, once highlighted you can select ON or OFF by pressing the or button. IMPORTANT: The AC cord should not be disconnected during the operation of Winter mode function.
When in winter mode, power consumption is higher than normal standby consumption. This is entirely due to the operation of heating circuitry. We strongly recommend to turn off Winter mode when the DPELHQWWHPSHUDWXUHLVDERYHÛ)Û&
N RC inhibition
You can prevent unwanted remote control operation by selecting RC Inhibition.
Select using the or button. Press the or button to select On or Off.
To
N Child Lock
You can prevent unwanted operation of the LCD monitor via the buttons on the rear of the monitor.
Select using the or button. Press the button to select 2QRU2))7KH³&KLOG/RFN´26'ZLOODSSHDULIEXWWRQVDUHSUHVVHG ZKHQFKLOGORFNLV2Q
6WDQGE\RSHUDWHVQRUPDOO\ZKHQFKLOGORFNLVVHW³2Q´
With no picture input signal to AV1, RGB, AV2(YPbPr), AV3, DVI, 1HWZRUNVHWWXUQVRIIDXWRPDWLFDOO\6HOHFW³$9$XWR6KXW2II´XVLQJ the or button, once highlighted you can select On or Off by pressing the or button.
N Network Standby
<RXFDQVDYHSRZHUFRQVXPSWLRQVHOHFWLQJ³2II´DW1HWZRUN6WDQGE\ in Installation mode, both RS232C and
N On Timer Function
You can save power consumption selecting “Off” at On Timer function in Installation mode. On Timer in Time menu does not functional. To PDNHWKHPIXQFWLRQDOVHOHFW³21´LQWKLVPHQX
N LED Light setting
Select LED Light setting using the or button, once highlight- ed you can select On or Off by pressing the or button.
NDCR
The picture contrast improved while DCR is ON. Select DCR using the or button, once highlighted you can select On or Off by pressing the or button.
N Network Initial
This function automatically installs the IP Address, Subnet, Gateway and DNS information.
N Temperature Error
The recorded number of abnormal temperature is occurred is indi- cated here.
N IP Address/Subnet/Gateway/DNS
These 4 items display the
Disconnecting the mains supply before exiting Installation Mode will cancel the following features On program, RC inhibition, Address and Baud Rate.
11