Roland TU-400, TU-60, TU-70, TU-500 user manual Operation Panel, Adjusting the Sensors Position

Page 11

4. Operation Panel

AUTO

 

 

 

 

 

 

 

MANUAL

 

 

 

 

 

 

Material is taken up automatically

 

 

 

 

The material is taken up manually.

when material has been fed into the

 

 

 

 

 

 

 

 

 

 

 

 

sensor's detection area.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

BACKWARD

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Material take-up is in

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

the direction shown at

Power switch

 

 

 

 

 

 

 

 

 

 

 

 

 

 

right.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

FORWARD

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Material take-up is in

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

the direction shown at

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

right.

 

OFF

 

 

 

 

 

 

 

 

 

 

 

 

 

 

No material take-up occurs, even when

 

 

 

 

material has been fed into the sensor's

 

 

 

 

detection area.

 

 

 

 

5. Adjusting the Sensor's Position

Turn on the power. Two LEDs

1 (green and red) light up.

Loosen the screw as shown in the

2 figure, and adjust the angle of the sensor so that it is aligned with the mirror.

Tighten the adjustment screw

3 securely at the angle where the red LED has gone dark.

Screw

Green LED

Red LED

Sensor detection area

The TU performs material take-up when material is fed into this area.

LED goes dark

Sensor

Rear

Front

CJ/FJ

Mirror

Stand

9

Image 11
Contents Automatic media take-up unit EC Electromagnetic Compatibility Directive 89/336/EEC English Table of ContentsDo not disassemble, repair, or modify About the SymbolsTo Ensure Safe Use About and NoticesHands or hair may become caught Model name About the Labels Affixed to the UnitRating label Confirmation of Included Items System ConfigurationFront Installation and AssemblyFrame and Control Box Installation Top View Rail Slider InstallationInstalling the Sensor and the Small Retainer Front Rear Installing the MirrorPower Cord Connection and Large Retainer Installation Arm InstallationOperation Panel Adjusting the Sensors PositionFor the FJ Only Operating Conditions for the TUFor Both the CJ and the FJ For the CJ OnlySide view of flange Loading MaterialMounting the Flange and Paper Tube Correct Incorrect Loading Rolled MaterialCorrect IncorrectPrinted surface is moved to the inner side and taken up Securing the Material in PlacePrinted surface is moved to the outer side and taken up Starting Operation Removing Material MaintenanceTU doesnt take up material What to Do IfCJ doesnt run FJ doesnt runTU-60 TU-70 TU-400 TU-500 SpecificationsMemo R8-990901