Palsonic VCR9688 owner manual Hints on Programming, When two programmes overlap

Page 22

Hints on Programming

In Step 4, you can select various "EV" (every week) recording of the same channel at the same time modes as well as recording on a particular day. Press the V button when the current day on the calendar blinks or press the V button, exceeding the last day of the calendar (the day after one month). The DATE indication on the data set line will change in sequence.

EV-SU...EV-SA:

Recording on every specified day of the week. MO-FR: Recording every weekday

: changes with V button : changes with V button

 

 

The current

 

 

Other calendar

 

The day after

 

 

 

 

 

 

 

 

 

 

 

day

 

 

days

 

one month

 

 

 

 

MO-FR

 

 

 

EV-SA . . . . . . . EV-SU

 

 

 

 

 

 

 

 

 

 

 

 

When a timer recording is executed, the programmed data except for the everyday or weekly recording is erased.

If a power failure occurs or the power cord is un- plugged, the programmed data will be erased. (How- ever, the programmed data will last for 20 minutes). Reset the date and clock and re-programme the timer for recording.

Notes on Timer Settings

. The VCR will turn on 20 seconds prior to the pro- grammed recording start time and enter pause mode.

. Timer recording starts on time.

If the cassette has no safety tab when you press the OPERATE/TIMER button to put the VCR in timer recording standby mode, the cassette will be auto-

. matically ejected.

TIMER Recording Standby mode will not be acti- vated when the OPERATE/TIMER button is pressed for three seconds under the following conditions.

*There is not video cassette in the VCR.

*There is no programmed data.

.When two programmes overlap

If the start of the later programme overlaps with the recording period of the earlier programme, the ear- lier programme will be recorded to the end and then the later programme will be recorded. This means that the later programme will not be recorded during the overlapped period.

8:00 p.m.

10:00 p.m.

Programme 1

 

9:30 p.m.

11:00 p.m.

Programme 2

Not recorded

. If the same start time is set on two or more pro- grammes, the programme with the lowest number has the priority over the other programmes and will be recorded to the end. Then the programme with the next lowest number will be recorded. This means that the other programmes will not be recorded during the overlapped period.

8:00 p.m.

9:00 p.m.

Programme 1

 

8:00 p.m.

9:30 p.m.

Programme 2

 

Not recorded

E- 18

Image 22
Contents VCR-9688 How to Use This Manual Remote control unit Identification of Controls Front panel Rear panel Multi-displayRear Panel Remote Control UnitFront Panel Multi-displayMaintain Good Ventilation Contents Introduction Power Supply Cable InstallationConnection of VCR and TV Using Audio/Video Connector Equipment ConnectionPreparations Changing the Time after the Initial Setting Initial Setting UpChanging the Language after the Initial Settings To Execute AMS again after the Initial SettingMenu Screen/Mode Screen Using the Menu ScreenUsing the Mode Screen On Screen Display OSDAMS Operation Channel PresettingManual Tuning Automatic Channel ChangingPreperation for G-Code Instant Video Programming Channel Selection Tuning with the V CH V ButtonsTuning with the Number Buttons Remote Control Only Selecting AUX PositionBasic Operation Auto Head CleanerPlayback Digital Tracking ControlStill Frame Special Effect PlaybackSearch Frame AdvanceZero Return Minute SkipBlueback Function Recording Counter Display One-touch Timer Recording OTRCounter Function Changing OTR DurationProgramming procedure Programmable Timer RecordingBefore programming When two programmes overlap Hints on ProgrammingCode Instant Video Programming Extending the Recording TimeAbout Error Messages If the G-Code number is incorrectSymptom Cause Remedy OthersSpecifications General Section Palsonic Customer Service Telephone