MSB Technology DVD Audio Player user manual Screen is stretched or aspect does not change

Page 39

composite or S video connection and go to the video setup menu and change the output to Interlaced.

Screen is stretched or aspect does not change.

·The TV Screen setting in the Initial Settings menu is incorrect. Set it correctly for your TV/monitor.

·If your TV/monitor is connected using an S-video cable, try changing the S-Video Out setting.

Picture disturbance during playback or the picture is dark.

·This player is compatible with Macro-Vision System copy guard. Some discs include a copy prevention signal, and when this type of disc is played back, stripes, etc., may appear on some sections of the picture, depending on the TV. This is not a malfunction.

·Due to the player’s copy protection circuits, connection of this device through a VCR or an AV selector may prevent recording or cause picture problems. This is not a malfunction.

No audio, or audio is distorted.

·No audio is output during slow motion playback or when scanning discs other than audio CDs.

·Some DVD discs do not output digital audio: Switch your amplifier to the player’s analog outputs.

·Check that the disc is free from dust and dirt, and that it is not damaged.

·Check that all interconnects are firmly inserted.

·Check that you are connected to the outputs not the inputs.

·Check that the plugs and terminals are free of dirt, oxide, etc. and clean if necessary. Also check the cable for damage.

·Make sure the player’s output is not connected to the amplifier’s phono (turntable) inputs.

·Check your amplifier/receiver’s settings (volume, input function, speaker settings, etc.).

The analog audio is OK, but there appears to be no optical/coaxial digital audio signal.

·Make sure that the Digital Out setting is set to On.

·Check that a red light is shining out of the optical digital output. If so, it is most likely working and the problem is elsewhere.

·Check that the Dolby Digital, DTS and MPEG out settings are suitable for your amplifier/receiver—check the instruction manual that came with your amplifier/receiver.

·SACDS and some DVD-Audio discs do not output digital audio. Listen through the player’s analog audio outputs.

Noticeable difference in DVD and CD volume.

·This is due to differences in the audio format and is not a malfunction.

Noticeable difference in Player and pass-through volume.

·This is because the pass-through source does not match the player volume. Adjust the pass-through source volume. This is not a malfunction.

Cannot play multichannel audio.

·Make sure that Audio Output Mode is set to 5.1 Channel.

·Check that the Dolby Digital, DTS and MPEG Out settings are suitable for your amplifier/receiver—check the instruction manual that came with your amplifier/receiver.

·DVD-Audio and SACDs do not output multichannel digital audio. Listen through the player’s analog outputs.

·Check that the settings in the Speaker Installation screen are correct.

·Check the audio options available from the disc menu.

Cannot listen to high-sampling rate audio through the optical/coaxial digital output.

·Make sure that Linear PCM Out is set to Down Sample Off .

·Use the MSB Network output.

·As a copy-protection measure, some DVDs do not output 96kHz audio. In this case, even if set to Down Sample Off, the player automatically outputs the audio at 48 kHz. This is not a malfunction. Use the MSB Network for full resolution.

Cannot output 192kHz or 176.4kHz digital audio from optical/coaxial output.

·The player does not output digital audio from the optical/coaxial jacks at these sampling rates. The digital output is automatically downsampled. Use MSB Network output.

Audio is distorted and full of static on a particular DVD-Audio track or disc but DVDs and CDs play fine.

·Check if the disc is recorded in 44.1 kHz sampling rate (press display button on remote) and if the digital output is enabled (Is a red light coming out of the optical digital output?) If so, go to initial setup menu and turn off the digital output.

Cannot output 96kHz or 88.2kHz digital audio from optical/coaxial output.

·Check that Linear PCM Out is set to Down Sample Off.

·Some discs are digital copy protected and do not output high sampling rate digital audio. In this case the output is automatically downsampled. Use the MSB network output.

No DTS audio output from optical/coaxial output.

·If this unit is connected to a non-DTS compatible amplifier or decoder using a digital audio cable, set DTS Out to DTS>PCM. If you do not do this, noise will be output when you play a DTS disc.

·If this unit is connected to a DTS-compatible amplifier or decoder using a digital audio cable, check the amplifier settings,

39

Image 39
Contents Super DVD Audio Player Contents Player Settings using the On Screen Menus IEEE1394 Setup Or Projector. It is a complete system. If Unique Features and Unprecedented Performance Preamp UpgradeBurn-In Features Disc/Content Format Playback Compatibility Using the remote controlsDVD-Video regions System Design and Connections Stand alone systemEnhanced Audio system Enhanced Home Theater Design Add to a complex home theaterRear Panel Details InputsVideo Outputs Analog Audio Outputs Digital Audio OutputsMSB Network Creating an IEEE1394 network IEEE1394 NetworkDisplay Front Panel ControlsRemote controls Simple Volume RemoteComplete Remote Page Configuration Options Player Setup Eight Channel Audio ConfigurationStereo Standard Configuration Setup OperationsHome Theater Standard Stereo Bi Amp ConfigurationStereo Tri Amp Configuration ConfigurationCenter Channel Downmixing Home Theater with Blended Mono Stereo SubsHome Theater with Blended Sides Home Theater with Downmixed CenterHome Theater with Center Rear Master Slave ModeSetting up with the Setup Navigator Player Settings using the On Screen MenusSwitching on Using the on-screen displaysDVD disc menus Front panel and small remote controlsPlaying discs Basic playback controlsFAQ Scanning discs Using the Disc Navigator to browse the contents of a discUsing the Multi Dial IntroductionLooping a section of a disc Using repeat playUsing random play Frame advance/frame reverseCreating a program list Editing a program listOther functions available from the program menu Switching DVD-Audio audio channel Switching subtitlesSwitching DVD-Video audio language Switching DVD-RW audio channelVideo Settings Menu Audio Settings MenuDigital Out Default setting On Using the Initial Settings menuDigital Audio Out settings Creating your own presetsLanguage settings Video Output settingsOptions Display settingsBonus Group Auto Disc Menu Default setting OnGroup Playback Default setting Single DVD Playback Mode Default setting DVD-AudioSpeakers Sacd Playback Default setting 2ch AreaCD Playback Default setting PCM Playback Audio Output Mode Default 2 ChannelAdditional Information IEEE1394 SetupStandard TV users About the audio output settingsScreen sizes and disc formats Widescreen TV usersLanguage code list Selecting languages using the language code listGlossary No sound out of the 8 analog outputs TroubleshootingScreen is stretched or aspect does not change IEEE1394-related messages IEEE1394 troubleshootingLimited Warranty Care and Placement of the PlayerUpgrades and Modifications