Motorola DVD operating instructions To Test

Page 40

I n s t r u c t i o n s : P o w e r , V o l u m e , M u t e , T V I n p u t

seconds (until the red light at the end of the remote lights up and stays on when you release the buttons).

To Control:

TV power, volume,

TV input only

A/V system

A/V system

mute, and TV

 

power

volume and

 

 

 

Input

 

 

mute

 

 

 

 

 

Press the:

TV PWR and TiVo

TV INPUT and

TV PWR and TiVo

MUTE and TiVo

buttons

TiVo buttons

buttons

buttons

 

 

 

 

 

 

2.Enter the search code. Refer to the table below and use the number keys on your remote control to enter the appropriate code.

To Test:

TV power, volume,

TV input only

A/V system

A/V system

mute, and TV Input

 

power

volume and mute

 

 

 

 

 

 

 

Enter:

0999

0999

1999

1999

 

 

 

 

 

 

 

 

 

After you press the fourth digit of the code, the red light on the end of the remote

4

 

control will flash twice, then remain on.

 

3.Test the remote control. Point the remote control at the TV or A/V receiver. Press CHAN UP to test the first code. The test is successful if the TV or A/V receiver responds (by powering off, changing input, or muting, depending on the function you are trying to program). If there is no response, wait two or three seconds, then press CHAN UP again. Continue doing this until the TV or A/V receiver responds.

When the TV or A/V receiver responds, press ENTER to select the current code. The red light at the end of the remote control will flash three times to indicate that the remote control is properly coded to control your device.

35

Image 40
Contents Installation Guide Pioneer DVD Recorder with TiVo Compatibility of this unit with progressive-scan TVs Table of Contents Troubleshooting Getting Started FCC Note Federal Communications Rule A r C u s t o m e r Using This Guide Understanding the basicsFinding your setup example What’s next?Cables and Accessories These are the basicsChoosing audio and video cables Connecting to the Phone Line Using Your Recorder with a Cable or Satellite Box Serial/Data ControlIR Infrared Control Secure the material, making sure that it fits snugly T t i n g S t a r t e d Common Setup Examples Setup 1 Antenna or Cable No Cable Box RecorderTelevision Before you beginT u p 1 a n t e n n a o r C a b l e N o C a b l e B o Setup 2 Cable Box or Satellite Receiver See , Connecting to a Home Network, in the User’s Guide M m o n S e t u p E x a m p l e s Additional Setup Examples Connecting a VCR or a Video CameraSetup 3 Watching One Channel While Recording Another Recorder TelevisionYou can also watch one channel Setup 4 Both a Satellite Box and an RF Program Source RecorderRecord DVDs Service is required. Setups Before you begin Upgrade to TiVo PlusUpgrade Satellite Box Cable Box Recorder Cable or Satellite Box Data Connector Connection and for alternatives to Serial Control cable, see Connecting a VCR or a Video Camera To connect a VCR Before you beginTo connect a video camera not shown Setting Up the Remote Control Using the Remote with a TV and A/V Stereo System T t i n g U p t h e R e m o t e C o n t r o lInstructions Power, Volume, Mute, TV Input System Mute, and TV Power Volume InputTV input only System Mute, and TV Power Volume Input Performing a Code SearchTo Test T t i n g U p t h e R e m o t e C o n t r o l Managing Multiple Recorders and Remotes Resetting the Programmable Buttons Troubleshooting Customer Support TroubleshootingCustomer Support Use this chapterTroubleshooting Why does the Recorder have to be connected to a phone line?My phone jack isn’t near the Recorder Do I need to keep the phone connected all the time?Troubleshooting My Recorder remote control doesn’t work with my Recorder Troubleshooting Troubleshooting Troubleshooting Front and Back Panel Reference Front Panel Reference Back Panel ReferenceFront Panel Reference O n t P a n e l R e f e r e n c e P e n d i x a Back Panel Reference 12 14P e n d i x a C k P a n e l R e f e r e n c e P e n d i x a Index D e Page D e Specifications Troubleshooting