FUNAI TB100MW9 owner manual Precautions, Location

Page 4

BEFORE USING

Precautions

Location

For safe operation and satisfactory performance of this product, keep the following in mind when select- ing a place for its installation:

•Shield it from direct sunlight and keep it away from sources of intense heat.

•Avoid dusty or humid places.

•Avoid places with insufficient ventilation for proper heat dissipation. Do not block the ventilation holes at the top and bottom of the unit. Do not place the unit on a carpet because this will block the ventila- tion holes.

•Install unit in a horizontal position.

•Avoid locations subject to strong vibration.

•Do not place this product near strong magnetic fields.

•Avoid moving this product to locations where tem- perature differences are extreme.

Avoid the Hazards of Electrical Shock and Fire

•Do not handle the power cord with wet hands.

•Do not pull on the power cord when disconnecting it from an AC wall outlet. Grasp it by the plug.

•If by accident, water is spilled on your unit, unplug the power cord immediately and take the unit to our Authorized Service Center for servicing.

•Do not put your fingers or objects into this product cassette holder.

•Do not place anything directly on top of the unit.

IMPORTANT COPYRIGHT INFORMATION

Unauthorized recording or use of broadcast televi- sion programming, video tape, film or other copy- righted material may violate applicable copyright laws. We assume no responsibility for the unauthor- ized duplication, use or other acts which infringe upon the rights of copyright owners.

FCC WARNING- This equipment may gener- ate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction man- ual. The user could lose the authority to oper- ate this equipment if an unauthorized change or modification is made.

This equipment has been tested and found to com- ply with the limits for a Class B digital device, pur- suant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be deter- mined by turning the equipment off and on, the user is encouraged to try to correct the interfer- ence by one or more of the following measures:

1)Reorient or relocate the receiving antenna.

2)Increase the separation between the equipment and receiver.

3)Connect the equipment into an outlet on a cir- cuit different from that to which the receiver is connected.

4)Consult the dealer or an experienced radio/TV technician for help.

4

EN

X6040UD_Book.indb 4

10/22/2007 5:09:10 PM

Page 3 Page 5
Image 4
Page 3 Page 5
Contents TB100MW9 Before Using Risk of Electric Shock Do not OpenBefore Using Precautions LocationTable of Contents Information on Digital Broadcasting Major Features of STBTrademark Information Before Using Location of ControlsAccessories Installing Batteries Snap the battery cover backConnecting an Antenna When Connecting to Cable Box optional AlsoConnections Basic ConnectionConnecting to TV Supplied cables used in this connection are as followsOther Connections STB Connection to a Standard Stereo SystemConnecting to TV and Video Devices VCR, DVD Recorder, etc DVD RecorderInitial Setup Select Autoscan using K / L, then press OK Initial Setup Setup WizardTo cancel during scanning Selecting Channels on the STB Channel BannerChoosing Audio Language Picture StillAdvanced Operation Adding/Deleting ChannelsAdjusting Antenna Press Setup to exit Setup menuReceiving Channels Autoscan Select the channel number you want toSelecting Display Mode Select Display Mode using K / L, then press OKTo cancel during scanning Press Setup or OK When no Signal appears on the screenSetting the Time Zone and DST Daylight Saving Time Select Time Zone using K / L, then press OKSelect D.S.T using K / L, then press OK Select on or OFF using s / B, then press OKSelect Mpaa Rating using K / L, then press OK Enter the password using the number buttonsSee the following description for setting each item Chip OptionsSelect TV Rating using K / L, then press OK Password entry fieldFollow steps 1-3 in V-Chip Options On page 21, then enter 4737Enter the new 4-digit password using the number buttons Select DTV CC using K / L, then press OKSelect CC Style using K / L, then Closed Caption OptionsAuto Power Down Select desired amount of time using K / L, then press OKSymptom Remedy TroubleshootingOthers Specifications Glossary and AcronymsGuía Para Rápida Consulta Antes de utilizarConexiones Conexión básicaCuando conecte tambien a la caja de cable opcional Observación para el instalador del sistema de cable de TVAjuste inicial Guía Para Rápida ConsultaAsistente de ajustes Para cancelar durante la exploración Presione OK Seleccione RF Fuera siMemo Limited Warranty
Top Page Image Contents