Sony KV-G142M service manual Connections

Page 5

Getting Started

Connections

Connecting a VHF antenna or a combination VHF/UHF antenna

75-ohm coaxial cable (round)

Attach an optional IEC antenna connector to the 75-ohm coaxial cable.

Plug the connector into the (antenna) socket at the rear of the TV.

Connecting optional equipment

You can connect optional audio/video equipment to your TV such as a VCR, multi disc player, camcorder, or video game.

Connecting video equipment using the É(video input) jack

Front of TV

ÉCamcorder

D ³

to video and audio outputs

to É

(video input)

D(video) and

³(audio) inputs

: Signal flow

Rear of TV

Rear of TV

On a wall

or

to antenna socket

Rear of TV

³ D

É

Öò

to antenna output

VCR

5 –

Connecting an indoor antenna

3

2

Ö³

D

 

 

 

 

ÖÉò

 

 

Öò

 

to É

to video

(video input)

and audio

outputs

D(video) and

³(audio) inputs

: Signal flow

When connecting video equipment to the É(video input) jack

Do not connect video equipment to the É(video input) jacks at the front and the rear of your TV simultaneously; otherwise the picture will not be displayed properly on the screen.

Connecting audio/video equipment using the ò(monitor output) jack

to antenna socket

1

Note

∙ You are advised to use an outdoor antenna for better reception.

Rear of TV

³ D

É

Öò

to ò

(monitor output)

D(video) and

³(audio) outputs

to antenna output

VCR

to video and audio inputs

: Signal flow

When recording through the ò(monitor output) jack

Do not change the channel or video input while recording with a VCR; otherwise the channel or video input you are recording also will be changed.

4-EN Getting Started

Getting Started

5-EN

 

 

 

KV-G14M2 RM-869

Image 5
Contents Trinitron Color TV Channel coverage SpecificationsTable of Contents Progr + Connections Presetting channels Watching the TV Adjusting the picture Rear Cover Removal F1 Board Removal Section DisassemblyBoard Removal Service Position Demagnetization Coil Removal Replacement of PartsTerminal Board Bracket Removal Picture Tube Removal ∙ Removal of ANODE-CAP ∙ Removing ProceduresBeam Landing Section SET-UP AdjustmentsHorizontal and Vertical Static Convergence ConvergenceDynamic Convergence Adjustment Preparation Focus AdjustmentMethod of Cancellation from Service Mode G2 Screen and White Balance AdjustmentsMemory Section Self Diagnosis FunctionNonvolatile Adjustments with Commander Section Circuit AdjustmentsAdjustment Method Adjustment Item Table OFM Item No VPX Picture Distortion Adjustment Board Adjustment After IC003 Memory ReplacementChassis SectionExploded View F35430206 Electrical Parts ListDiode D1NL20 DescriptionDiode EL1Z Diode GP08DCarbon REF.NOREF.NO. Part no Description Remark WirewoundFusible MetalSpark GAP SwitchGAP, Spark FILTER, Surface Wave TransformerScrew +BVTP HOLDER, FBTCapacitor Ceramic Chip3KV REF.NO. Part no Description2KV PLUG, Connector 3P PLUG, Connector 6PCeramic Chip 1MF FilterCOIL, VAR, Ferrite HWC JACK, PIN 2P Chip ConductorTransistor 2SC1623-L5L6 Transistor DTC143TKA-T146220 10W R040 300 Thermistor Positive Tuner TRANSFORMER, Line FilterThermistor Transistor 2SC2611 SOCKET, CRTTransistor 2SC2611 Resistor Carbon Variable ResistorMANUAL, Instruction Remote CommanderBattery COVER, Remote Commander Sony Corporation