Pioneer SC-35 manual Select ‘Channel Level’ from the Manual SP Setup menu

12The System Setup and Other Setup menus

•Surr – Select LARGE if your surround speakers reproduce bass frequencies effectively. Select SMALL to send bass frequencies to the other speakers or subwoofer. If you didn’t connect surround speakers choose NO (the sound of the surround channels is sent to the front speakers or a subwoofer).

•SB – Select the number of surround back speakers you have (one, two or none).1 Select LARGEx2 or LARGEx1 if your surround back speakers reproduce bass frequencies effectively. Select SMALLx2 or SMALLx1 to send bass frequencies to the other speakers or subwoofer. If you didn’t connect surround back speakers choose NO.

•SW – LFE signals and bass frequencies of channels set to SMALL are output from the subwoofer when YES is selected. Choose the PLUS setting if you want the subwoofer to output bass sound continuously or you want deeper bass (the bass frequencies that

would normally come out the front and center

speakers are also routed to the subwoofer).2 If you did not connect a subwoofer choose NO (the bass frequencies are output from other speakers).

3Select ‘X. OVER’ and set the crossover frequency.3 Frequencies below this point will be sent to the subwoofer (or LARGE speakers).

4When you’re finished, press RETURN.

You will return to the Manual SP Setup menu.

Channel Level

Using the channel level settings, you can adjust the overall balance of your speaker system, an important factor when setting up a home theater system.

1Select ‘Channel Level’ from the Manual SP Setup menu.

•AUTO – Adjust channel levels as the test tone moves from speaker to speaker automatically.

3 Confirm your selected setup option.

The test tones will start after you press ENTER.

4 Adjust the level of each channel using /.

If you selected MANUAL, use / to switch speakers. The AUTO setup will output test tones in the order shown on-screen:

Adjust the level of each speaker as the test tone is emitted.4

5When you’re finished, press RETURN. You will return to the Manual SP Setup menu.

Tip

•You can change the channel levels by set the remote

control to the receiver operation mode, then press CH LEVEL, and then using / on the remote control.

Speaker Distance

For good sound depth and separation from your system, you need to specify the distance of your speakers from the listening position. The receiver can then add the proper delay needed for effective surround sound.

1Select ‘Speaker Distance’ from the Manual SP Setup menu.

2Adjust the distance of each speaker using /.

You can adjust the distance of each speaker in 1/2 inch Increments.

3When you’re finished, press RETURN. You will return to the Manual SP Setup menu.

Tip

2Select a setup option.

•MANUAL – Move the test tone manually from

speaker to speaker and adjust individual channel levels.

•For best surround sound, make sure the surround back speakers are the same distance from the listening position.

Note

1• If you selected ZONE 2 or Front Bi-Amp(in Speaker system setting on page 115) you can’t adjust the surround back settings.

•If the surround speakers are set to NO, the surround back speakers will automatically be set to NO.

2If you have a subwoofer and like lots of bass, it may seem logical to select LARGE for your front speakers and PLUS for the subwoofer. This may not, however, yield the best bass results. Depending on the speaker placement of your room you may actually experience a decrease in the amount of bass due low frequency cancellations. In this case, try changing the position or direction of speakers. If you can’t get good results, listen to the bass response with it set to PLUS and YES or the front speakers set to LARGE and SMALL alternatively and let your ears judge which sounds best. If you’re having problems, the easiest option is to route all the bass sounds to the subwoofer by selecting SMALL for the front speakers.

3• This setting decides the cutoff between bass sounds playing back from the speakers selected as LARGE, or the subwoofer, and bass sounds playing back from those selected as SMALL. It also decides where the cutoff will be for bass sounds in the LFE channel.

•With Full Auto MCACC Setup or Auto MCACC Setup (ALL or Speaker Setting), the setting here will not apply and the crossover frequency will be automatically set. Crossover frequency is a frequency aimed at achieving the optimal sound field taking into account the bass capacity of all connected speakers and human aural characteristics.

•If you’re using THX speakers, confirm that the crossover frequency is set to 80Hz.

4If you are using a Sound Pressure Level (SPL) meter, take the readings from your main listening position and adjust the level of each speaker to 75 dB SPL (C-weighting/slow reading).

116

En