Pioneer SC-35 manual Plugging in the receiver, Unit, a piece of furniture, or other object on

03Connecting your equipment

Switching components on and off using the 12 volt trigger

You can connect components in your system (such as a screen or projector) to this receiver so that they switch on or off using 12 volt triggers when you select an input function. However, you must specify which input functions switch on the trigger using the The Input Setup menu on page 45. Note that this will only work with components that have a standby mode.

Plugging in the receiver

Only plug in after you have connected all your

components to this receiver, including the speakers.

1Plug the supplied power cord into the AC IN socket on the back of the receiver.

2Plug the other end into a power outlet.1

CAUTION

OUT 1

OUT

• Handle the power cord by the plug part. Do not pull

1 4

BD

IN

IN

IN

IN

(CONTROL)

out the plug by tugging the cord, and never touch the

HDMI

IN

1

2

3

4

ASSIGNABLE

power cord when your hands are wet, as this could

IN 1

(DVD)

COMPONENTVIDEO

ASSIGNABLE

IN 2

(DVR/BDR)

MONITOR

cause a short circuit or electric shock. Do not place

VIDE

OUT

IN 3

(VIDEO)

ZONE2

ZONE3

DVD

TV/SAT

VIDEO

DVR/BDR

PHONO

CD

the unit, a piece of furniture, or other object on the

OUT

OUT

IN

IN

IN

OUT

IN

IN

IN

MONITOR OUT

power cord or pinch the cord in any other way. Never

ZONE 2 OUT

make a knot in the cord or tie it with other cables. The

Y

PB

PR

GND

power cords should be routed so that they are not

SIGNAL

likely to be stepped on. A damaged power cord can

ANTENNA

R

FRONT HEIGHT/W

SPEAKERS

cause a fire or give you an electric shock. Check the

Class 2Wiring

RS-232C

AM LOOP

FM UNBAL 75

12V

power cord once in a while. If you find it damaged,

CONTROL

IN 1 IR

SEE INSTRUCTION

SELECTABLE

IN

1 TRIGGER

MANUAL

ask your nearest Pioneer authorized independent

(OUTPUT 5 V

(OUTPUT

VOIR LE MODE

SELECTABLE

150 mA MAX)

OUT

IN 2

12V

D'EMPLOI

service company for a replacement.

TOTAL

2

150 mA MAX)

CU-RF100

OUT

• Do not use any power cord other than the one

12 V TRIGGER

supplied with this unit.

INPUT

• Do not use the supplied power cord for any purpose

other than that described below.

•Connect the 12 V TRIGGER jack of this receiver to the 12 V trigger of another component.

Use a cable with a mono mini-plug on each end for the connection.

After you’ve specified the input functions that will switch on the trigger, you’ll be able to switch the component on or off just by pressing the input function(s) you’ve set on page 45.

It is also possible to have the component switch not when the input function is switched, but when HDMI OUT is switched. For details, see HDMI Setup on page 73.

•The receiver should be disconnected by removing the mains plug from the wall socket when not in regular use, e.g., when on vacation.

•Make sure the blue  STANDBY/ON light has gone out before unplugging.

•If you have connected speakers with a 6 Ω

impedance, change the impedance setting before turning on the power.

Note

1After this receiver is connected to an AC outlet, a 2 second to 10 second HDMI initialization process begins. You cannot carry out any

operations during this process. The HDMI indicator in the front panel display blinks during this process, and you can turn on this receiver once it has stopped blinking. When you set the Control with HDMI to OFF, you can skip this process. For details about the Control with HDMI feature, see Control with HDMI function on page 72.

42

En