Pioneer PRO-1120HD, PRO-920HD Connecting the VCR controller, Screen for recording test appears

Page 59

Enjoying through External Equipment

12

Connecting the VCR controller

Connect the supplied VCR controller to the Media Receiver. This allows you to preset digital TV programs for recording; see page

48.When the specified time comes, the system in the standby mode is automatically switched on and the specified TV program is recorded using the connected VCR or DVD recorder.

Make sure to leave the VCR power on when presetting TV programs for recording with the VCR controller.

Be sure to firmly connect the VCR controller to the VCR control terminal on the rear of the Media Receiver. If you have mistakenly connected it to the CONTROL IN or CONTROL OUT terminal, remote control or other operations may be disabled.

Use the following procedure to set the manufacture of the recording equipment:

1Press HOME MENU.

2Select “Tuner Setup”. (/ then ENTER)

3Select “Recorder Setup”. (/ then ENTER)

4Select “VCR Setup”. (/ then ENTER)

5Select the manufacture of the recording equipment. (/ then ENTER)

Recorder Setup

VCR Setup

 

VCR Setup

 

xxxxxxxxxxxxxxxxxxxxx

• XXXXX

xxxxxxxxxxxxxxxxxxxxx

 

XXXXX

xxxxxxxxxxxxxxxxxxxxx

 

XXXXX

 

 

 

Home Menu Exit

English

Media Receiver (rear view)

• The screen for recording test appears.

I N

OUT

VCR CONTROL

CONTROL

IN

 

 

 

ANTENNA B

 

 

S-VIDEO

SERVICE ONLY

 

 

 

OUT

 

 

MONITOR OUT S-VIDEO

DIGITAL O

OPTICA

ANTENNA/

Cable

 

 

 

 

CABLE A IN

CARD

 

 

 

 

 

 

(TS)

S400

 

 

INPUT 2

 

 

INPUT 1

COMPON

VIDEO

R-AUDIO-L

VIDEO

R-AUDIO-L

Y

CB/

VIDEO

R-AUDIO-L

S-VIDEO

R-AUDIO-L IINPUT 33

Y

CB/

(Once you have positioned the VCR controller, secure with the supplied tape.)

6 Check that the power to the recording equipment is on,

and insert tape into the slot.

• Insert tape you think it all right to erase its contents.

The contents will be erased because Rec and Stop

codes are output in the test.

• Check that the light emitting section on the VCR

controller cable faces the recording equipment.

7 Press A to execute recording test.

• If the recording equipment fails to start and stop

recording, check and change the specified recording

equipment manufacture.

VCR CONTROL

VCR or DVD recorder

Position the light emitting section on the VCR controller cable so that it faces the VCR.

Remote control sensor

8

Press A to select “Yes, Store Setting”.

9

Press HOME MENU to exit the menu.

.

Even if you correctly specify the manufacture of the recording equipment, control of some models may be disabled.

Perform the recording test when the recording equipment is not in recording standby or is not recording.

The recording test takes approximately 10 seconds.

The PIONEER has been set as the factory default.

59

En

Image 59
Contents PRO-1120HDPRO-920HD Page PRO-435PU Information to UserFor Canadian model Contents Enjoying through External Equipment Adjustments and SettingsTimer Presetting Useful Remote Control FeaturesUsage guidelines Installation guidelinesImportant User Guidance Information About operations through i.LINK Panel sticking and after-image lagAfter-image lagging due to remaining electric load After-image lag image due to burningSafety Precautions Mounting hole Installation PrecautionsWhen using other items Rear viewOperational Precautions Media Receiver Supplied AccessoriesPlasma Display Front view Power buttonPart Names Front view Right view Rear viewComponent Video Y, CB/PB, CR/PR Favorite CH A, B, C, D Remote control unitCH +/- Selects the channel Return Returns to the previous menuPreparation Installing the Plasma DisplayUsing the optional Pioneer stand Using the optional Pioneer speakers Operating EnvironmentInsert the stand into the side of the Media Receiver Installing the Media ReceiverInstalling the Media Receiver vertically Plasma Display Media ReceiverShock absorbing pad Plug the screw holes using the supplied capsRemove the shock absorbing pads That came with the speaker System cable Connecting the system cableAttaching and removing speed clamps When the speakers are installed on the sides Rear viewRouting cables Attaching speed clamps to the main unitInserting batteries Preparing the remote control unitAllowed operation range of the remote control unit Media Receiver rear Connecting VHF/UHF antennasConnecting VHF/UHF antennas and a Cable Converter VHF antenna UHF antenna MixerInserting the cable card Switching between antenna a and BPower cord Noise filter Connecting the power cordBasic Operations Turning on the power StandbyTurning off the power Standby Changing channels Watching TV channelsSelecting the antenna VOL + also quits muting Changing the volume and soundVolume adjustment Muting Viewing a channel bannerStereo broadcasts Using the POD serviceSetting MTS/SAP mode Changing the languageSplitting the screen Using the multiscreen functionsNormal image Freezing imagesPC mode menus Menu SetupMenu configuration AV mode menusSetting for skipping unwanted channels Tuner SetupSetting up TV channels Using Auto Channel PresetEnabling data acquisition Checking signal strengthNaming TV channels Checking the Cable Card IDTV ratings Changing the passwordParental Control Voluntary movie rating system MpaaActivating the Parental Control Clearing the passwordSetting the voluntary movie rating system Mpaa Use the following procedure to clear the passwordBlocking Not Rated TV programs Setting the TV ratingsSetting the TV Parental Guidelines TV Guidelines Canadian French ratings Setting Canadian English ratingsCanadian rating systems Canadian English ratingsTemporarily deactivating the Parental Control Setting your favorite channelsSetting up closed captions Setting Canadian French ratingsCaptions Off Factory default On If MuteActivating the closed caption Selecting digital closed captionsSelection Clock SettingFor AV source Adjustments and SettingsSleep Timer AV SelectionPro Adjust Picture adjustmentsCyan Color ManagementColor Temp YellowFront Surround Sound adjustmentsPower Management PC mode only Power ControlNo Signal off AV mode only No Operation off AV mode onlyEnglish PC mode except for XGA signals AV modePC mode except for XGA signals Dot by Dot PC mode for XGA signalsSelect Option Then Enter Select Language Select a language Language settingAccording to the brightness of images Icon Meaning Timer PresettingPresetting TV programs using the timer Priority rules for overlapped presettings Watching a VCR image Watching a DVD imageEnjoying through External Equipment Using Hdmi InputConnecting Hdmi equipment Displaying an image of the game console or camcorder Recording digital TV programs using a VCR or DVD recorderConnecting a game console or camcorder Enjoying a game console or watching camcorder imagesVCR or DVD recorder Connecting other audio equipmentConnecting a recorder Connecting an AV receiverWatching a D-VHS image Useful information PrecautionsDisplaying a D-VHS image Useful and important notificationTo change the order of devices Setting up for controlling a D-VHS recorderEditing the i.LINK list To change the name of a deviceNo data relay Setting up for i.LINK standbyStandby mode Link device Media Receiver i.LINK device Operating the control panel screenDisplaying an image from a personal computer Computer compatibility chartConnecting a personal computer Watching an image from a personal computerScreen for recording test appears Connecting the VCR controllerManufacture Lists of controllable recording equipment manufacturesAbout SR+ Connecting control cordsUsing the learning function Useful Remote Control FeaturesLearning function of the remote control unit Presetting manufacture codesCABLE/SAT VCR DVD/DVR Manufacture codesSelects the input source connected to the receiver Using the remote control unit to control other devicesTurns the receiver power on and off Receiver control buttonsCH + Mode switch with CBL/SAT selectedTurns the cable converter power on and off Cable control buttonsEnter Turns the Satellite broadcast tuner power on and offSAT control buttons VCR control buttons Mode switch with VCR selectedDVD/DVR control buttons Code Message TroubleshootingProblem Possible Solution AppendixAppendix Original SSLeay License Preamble Linux Source Notice GNU General Public LicenseAppendix How to Apply These Terms to Your New Programs No WarrantyGNU Lesser General Public License Appendix Appendix How to Apply These Terms to Your New Libraries Media Receiver, Model PRO-R05U SpecificationsCopyright protection TrademarksPioneer Corporation