RCA LCDX3022W manual Learning Feature, How to Use the Remote After You’ve Programmed It

Page 17

Using the Remote Control

Using Direct Entry

1.Turn on the component to be programmed.

2.Look up the brand and code number(s) for the component on the code list in this section.

3.Press and hold the component button you want to program on the remote.

4.While pressing the component button, enter the code from the remote control code list. If the component button flashes, you have either entered an invalid code or the button isn’t programmable.

5.Release the component button.

6.Point the remote at the component. Press ON•OFF to see if the component responds to the command. If it doesn’t, try pressing the component button and then ON•OFF again.

•If you get no response, repeat these steps using the next code listed for your brand, until the component responds to the remote commands.

•If you try all the codes for your component brand and none work, try the automatic code search method. If automatic code search doesn’t find the code, the remote is not compatible with your component.

How to Use the Remote After You’ve Programmed It

Because this universal remote can operate several different components, it uses operational modes triggered by the component buttons. For example, if you want the remote to operate the TV, you would press the TV button to put the remote into TV mode before you could operate the TV.

1.Press the appropriate component button (DVD, VCR, etc.) to set the remote to operate the component.

2.Press ON•OFF to turn the component ON or OFF.

3.Use the remote buttons that apply to that component.

Note: If you keep pressing buttons and nothing happens, the remote is probably in the wrong mode. You must press the component button that matches the component you want to operate (i.e., if you want to operate the VCR, press VCR on the remote control to put the remote in VCR mode.)

The Learning Feature

Before using the learning feature, make sure this TV’s remote control is programmed to control other components you have connected to the TV. Programming the remote control erases all learned commands for that component mode.

After you program the TV’s remote control to operate the other component, the TV’s remote provides most of the operations you need. However, there may be some functions on the component’s original remote control that your TV’s remote control doesn’t have. For example, your DVD remote control might have an ANGLE button that enables you to change the angle of the picture, but your TV remote doesn’t have that button. The learning feature enables you to record the functionality of a specific button from the original remote control to one of the TV’s remote control buttons.

Note: All learned functions for a mode can be erased if you program a different component to that mode.

Chapter 2

Graphics contained within this publication are for representation only.

13

Page 16 Page 18
Image 17
Page 16 Page 18
Contents User’s Guide Product Registration Product Information Important InformationO U N D C L a M P S Important Safety InstructionsThis page left intentionally blank Table of Contents Other Information Using the Menu SystemThings to Consider Before You Connect Connections & SetupRGB Input Explanation of JacksBottom Panel Side Panel Cmpt Component InputVID1 Input Connect Your Cable Using the DVI JackChoose Your Connection Connection to AV ComponentsUsing the RGB Jack Using the Cmpt JackSet Up Your TV Adjust the Viewing Angle of the TVPlug in the TV Put batteries in the remoteComplete Channel Search Choose the Signal TypeChoose the Menu Language Button Descriptions for TV Mode Using the Remote ControlButton Descriptions for Other Modes Using the Input ButtonProgramming the Remote to Operate Other Components Using Automatic Code SearchFind Out If You Need to Program the Remote Programming the RemoteUsing Direct Entry Learning FeatureHow to Use the Remote After You’ve Programmed It Up to 2 inches apart Adding a Learned FunctionDeleting ALL Learned Functions Volume Punchthrough FeatureClearing a Learned Function Deleting ALL Volume Punchthrough Commands Remote Code ListPVR Codes Why You Should Use the Autotuning Feature Using the TV’s FeaturesHow to Set Up the Autotuning Feature About the Channel BannerAutotuning Using the PIP FeaturePIP Picture-in-PC Operation PIP ButtonsParental Controls PIP Problems?How V-Chip Works Parental ControlCanadian English V-Chip Rating System US V-Chip Rating SystemChip TV Ratings Canadian French V-Chip Rating SystemViewing Age-Based Ratings V-Chip Rating Limit ScreenBlocking Age-Based Ratings Viewing Specific Content Themes Blocking Specific Content ThemesChip Movie Rating Limit Chip TV RatingsBlocking Movie Ratings Blocking Canadian V-Chip RatingsViewing Movie Ratings French RatingsChannel Block Chip Unrated/Exempt BlockFront Panel Block Lock/Unlock Parental Controls Additional FeaturesMenus, On-screen Help, and Control Panels Using the Menu SystemExiting a menu ControlsChoice Lists Picture MenuNumeric Entries Option ListsSound Adv. Picture SettingsSound Menu Preferences Parental Control MenuPreferences Menu Timers Setup MenuSetup Channel ListPC Picture Size Menu PC Picture Quality MenuPC Sound Menu Picture SizeInformation Center PC Preferences MenuPC Information Center Other Information TroubleshootingCare and Cleaning Limited Warranty How State Law relates to warranty How to Order Accessory InformationFCC Information
Top Page Image Contents