RCA LCDX3022W manual Volume Punchthrough Feature, Clearing a Learned Function

Page 19

Using the Remote Control

Clearing a Learned Function

To delete a learned button function, use the procedure below.

1.Press and hold the component button (the component button lights). Then press and hold the CLEAR button for 3 seconds (the component mode button flashes—turns on and off again).

2.Release the component and CLEAR buttons (the component button being cleared turns on). Remote is now in Clear learned function mode.

3.Press and release the button where learning is to be cleared. The component button blinks off then back on—the learned function was cleared successfully.

4.Repeat steps 1 through 3 until all buttons’ learned functions have been cleared.

Note: If an invalid button is pressed, the component mode button(s) flashes 4 times and the selected component button stays on and remote remains in Clear Learned Function mode. Repeat step 3.

5.Press the CLEAR button to return the TV remote to its original operation mode.

Deleting ALL Learned Functions

This procedure erases all learned functions in every component mode of the remote.

1.Press and hold the CLEAR button (the current component button lights). Then press and hold the ON•OFF button (component button light turns off for 3 seconds, flashes, turns on and off) while continuing to hold CLEAR.

2.Release both buttons (current component button turns on).

3.Press any component button to delete all learned functions in all modes. Remote is automatically exited from this mode.

Note: Pressing the CLEAR button will NOT delete all learned functions, but will exit the Delete mode.

Volume Punchthrough Feature

You may find this feature helpful if you’ve connected your components to an audio/video receiver (A/V receiver) or amplifier, but you want to use the TV’s remote control to operate the volume for a component that is connected to the audio/video receiver. An example follows:

Let’s say you’ve connected your DVD player to your audio/video receiver. You’ve also programmed your TV remote control to operate your DVD player. Since the DVD player gets its volume through the audio/ video receiver, you would have to bounce back and forth between two remote controls: the A/V receiver’s remote to adjust the volume and the TV’s remote control to operate the DVD player.

The Volume Punchthrough feature eliminates the need for you to use two remote controls and saves a button press when you’re using the TV remote to adjust the volume. In effect, you are telling the TV remote to retrieve and send volume commands from the A/V receiver whenever the TV remote is in DVD mode.

Therefore, after you’ve successfully set up the Volume Punchthrough feature, whenever the TV remote is in DVD mode (press the DVD button) and you want to adjust the volume, you only have to press the VOL + or VOL- buttons. Follow the instructions below to set up Volume Punchthrough.

1.IMPORTANT: First, you must program the AUDIO button on the TV’s remote control to operate your audio receiver or amplifier. Go to page 12 for instructions. If you can’t program this remote to operate your audio receiver, Volume Punchthrough won’t work.

2.While setting up Volume Punchthrough, it’s best to point the remote away from components.

3.Decide which mode the remote will be in when the volume from the audio receiver “punches through.” The mode will be one of the component buttons (TV, DVD, SAT/CAB, VCR, or AUX/HD).

Chapter 2

Graphics contained within this publication are for representation only.

15

Page 18 Page 20
Image 19
Page 18 Page 20
Contents User’s Guide Product Registration Product Information Important InformationO U N D C L a M P S Important Safety InstructionsThis page left intentionally blank Table of Contents Other Information Using the Menu SystemThings to Consider Before You Connect Connections & SetupBottom Panel Explanation of JacksRGB Input VID1 Input Cmpt Component InputSide Panel Connection to AV Components Using the DVI JackConnect Your Cable Choose Your ConnectionUsing the RGB Jack Using the Cmpt JackPut batteries in the remote Adjust the Viewing Angle of the TVSet Up Your TV Plug in the TVChoose the Menu Language Choose the Signal TypeComplete Channel Search Button Descriptions for TV Mode Using the Remote ControlButton Descriptions for Other Modes Using the Input ButtonProgramming the Remote Using Automatic Code SearchProgramming the Remote to Operate Other Components Find Out If You Need to Program the RemoteHow to Use the Remote After You’ve Programmed It Learning FeatureUsing Direct Entry Up to 2 inches apart Adding a Learned FunctionClearing a Learned Function Volume Punchthrough FeatureDeleting ALL Learned Functions Deleting ALL Volume Punchthrough Commands Remote Code ListPVR Codes About the Channel Banner Using the TV’s FeaturesWhy You Should Use the Autotuning Feature How to Set Up the Autotuning FeaturePIP Buttons Using the PIP FeatureAutotuning PIP Picture-in-PC OperationParental Control PIP Problems?Parental Controls How V-Chip WorksCanadian English V-Chip Rating System US V-Chip Rating SystemChip TV Ratings Canadian French V-Chip Rating SystemBlocking Age-Based Ratings V-Chip Rating Limit ScreenViewing Age-Based Ratings Chip TV Ratings Blocking Specific Content ThemesViewing Specific Content Themes Chip Movie Rating LimitFrench Ratings Blocking Canadian V-Chip RatingsBlocking Movie Ratings Viewing Movie RatingsFront Panel Block Chip Unrated/Exempt BlockChannel Block Lock/Unlock Parental Controls Additional FeaturesControls Using the Menu SystemMenus, On-screen Help, and Control Panels Exiting a menuOption Lists Picture MenuChoice Lists Numeric EntriesSound Menu Adv. Picture SettingsSound Preferences Menu Parental Control MenuPreferences Channel List Setup MenuTimers SetupPicture Size PC Picture Quality MenuPC Picture Size Menu PC Sound MenuPC Information Center PC Preferences MenuInformation Center Other Information TroubleshootingCare and Cleaning Limited Warranty How State Law relates to warranty How to Order Accessory InformationFCC Information
Top Page Image Contents