RCA LCDX3022W manual Adding a Learned Function, Up to 2 inches apart

Page 18

Using the Remote Control

Adding a Learned Function

There are several things to consider before you begin the learning process:

•You can’t record a learned function to the following buttons on the TV’s remote control: component buttons (TV, VCR, DVD, SAT/CAB, AUX/HD, and AUDIO), the CLEAR button, and the LIGHT button.

•Before adding a Learned Function, you must program this TV’s remote control to operate that component because programming the remote control erases all learned commands for that component mode.

•Do the learning process in low light areas because too much natural light or fluorescent light might cause the learning feature to fail because the remote control functions are recorded (learned) by sending infrared (IR) signals.

•The TV’s remote and the original remote should be no more than 2 inches apart.

Up to 2 inches apart

•In order to record (learn) a function from one remote to the other, you must make sure the Infrared (IR) transmitter of the original remote is facing the IR receiver on the top of the TV’s remote (see illustration). To accomplish this, you may have to hold a remote in each hand instead of laying both on the table.

•The learned buttons are mode specific—if you add a button function from your DVD player’s remote control, you must press the DVD button first before the learned function will work (in TV mode, the button where you’ve stored the learned function will continue to work as it always has).

1.Press and hold the component button on the TV’s remote that applies to the function you will be adding (DVD, VCR, SAT/CAB, AUDIO, or AUX/HD). The component button lights.

2.On the TV remote, press and hold the RECORD button.

3.Keep pressing both of the buttons (the component button and the RECORD button) until the component button light turns off, flashes, and turns off. Release both buttons.

4.On the TV’s remote control, press and release the button where you want to store the new function (the component button turns off and then back on).

Note: If you press an invalid button on the TV remote, one of the component button flashes 4 times to alert you. You’ll have to repeat step 4.

5.With the remote controls facing each other and no more than 2 inches apart, press and hold the button of the component’s remote control that has the functionality you are recording to the TV’s remote control. Keep pressing the button until the TV remote’s component button light turns off and back on (the function has been saved to the TV remote). If all component buttons flash 4 times, the function wasn’t learned. Try again starting with Step 4.

6.The TV remote control remains in “learning mode” so you can continue adding functions to different buttons by repeating steps 4 and 5. Or, press CLEAR to exit learning mode.

Notes: If you want a new function on a button, you must record (learn) over it.

The amount of memory each learned function uses in the TV’s remote control varies. If your TV remote is out of memory, the component button(s) light flashes 4 times and turns off, exiting you from the Learning mode.

14

Graphics contained within this publication are for representation only.

Chapter 2

Page 17 Page 19
Image 18
Page 17 Page 19
Contents User’s Guide Important Information Product Registration Product InformationImportant Safety Instructions O U N D C L a M P SThis page left intentionally blank Table of Contents Using the Menu System Other InformationConnections & Setup Things to Consider Before You ConnectExplanation of Jacks Bottom PanelRGB Input Cmpt Component Input VID1 InputSide Panel Choose Your Connection Using the DVI JackConnect Your Cable Connection to AV ComponentsUsing the Cmpt Jack Using the RGB JackPlug in the TV Adjust the Viewing Angle of the TVSet Up Your TV Put batteries in the remoteChoose the Signal Type Choose the Menu LanguageComplete Channel Search Using the Remote Control Button Descriptions for TV ModeUsing the Input Button Button Descriptions for Other ModesFind Out If You Need to Program the Remote Using Automatic Code SearchProgramming the Remote to Operate Other Components Programming the RemoteLearning Feature How to Use the Remote After You’ve Programmed ItUsing Direct Entry Adding a Learned Function Up to 2 inches apartVolume Punchthrough Feature Clearing a Learned FunctionDeleting ALL Learned Functions Remote Code List Deleting ALL Volume Punchthrough CommandsPVR Codes How to Set Up the Autotuning Feature Using the TV’s FeaturesWhy You Should Use the Autotuning Feature About the Channel BannerPIP Picture-in-PC Operation Using the PIP FeatureAutotuning PIP ButtonsHow V-Chip Works PIP Problems?Parental Controls Parental ControlUS V-Chip Rating System Canadian English V-Chip Rating SystemCanadian French V-Chip Rating System Chip TV RatingsV-Chip Rating Limit Screen Blocking Age-Based RatingsViewing Age-Based Ratings Chip Movie Rating Limit Blocking Specific Content ThemesViewing Specific Content Themes Chip TV RatingsViewing Movie Ratings Blocking Canadian V-Chip RatingsBlocking Movie Ratings French RatingsChip Unrated/Exempt Block Front Panel BlockChannel Block Additional Features Lock/Unlock Parental ControlsExiting a menu Using the Menu SystemMenus, On-screen Help, and Control Panels ControlsNumeric Entries Picture MenuChoice Lists Option ListsAdv. Picture Settings Sound MenuSound Parental Control Menu Preferences MenuPreferences Setup Setup MenuTimers Channel ListPC Sound Menu PC Picture Quality MenuPC Picture Size Menu Picture SizePC Preferences Menu PC Information CenterInformation Center Troubleshooting Other InformationCare and Cleaning Limited Warranty How State Law relates to warranty Accessory Information How to OrderFCC Information
Top Page Image Contents