Panasonic TQBC2372-1 manual PC Input Terminals connection, Connections

Page 10

Connections

PC Input Terminals connection

COMPUTER

Conversion adapter (if necessary)

(Female)

AUDIO

PC IN

Mini D-sub 15p

RGB

PC cable

(Male)

Audio

Stereo plug

Connect a cable which matches

the audio output terminal on the computer.

Notes:

Due to space limitations, occasionally you may have trouble connecting Mini D-sub 15P cable with ferrite core to PC input Terminal.

With regard to the typical PC input signals that are described in the applicable input signals list (see page 50), adjustment values such as for the standard picture positions and sizes have already been stored in this unit. You can add up to eight PC input signal types that are not included in the list.

Computer signals which can be input are those with a horizontal scanning frequency of 15 to 110 kHz and vertical scanning frequency of 48 to 120 Hz. (However, the image will not be displayed properly if the signals exceed 1,200 lines.)

The display resolution is a maximum of 1,440 × 1,080 dots when the aspect mode is set to “4:3”, and 1,920 × 1,080 dots when the aspect mode is set to “FULL”. If the display resolution exceeds these maximums, it may not be possible to show fine detail with sufficient clarity.

The PC input terminals are DDC2B-compatible. If the computer being connected is not DDC2B-compatible, you will need to make setting changes to the computer at the time of connection.

Some PC models cannot be connected to the set.

There is no need to use an adapter for computers with DOS/V compatible Mini D-sub 15P terminal.

The computer shown in the illustration is for example purposes only.

Additional equipment and cables shown are not supplied with this set.

Do not set the horizontal and vertical scanning frequencies for PC signals which are above or below the specified frequency range.

Component Input is possible with the pin 1, 2, 3 of the Mini D-sub 15P Connector.

Change the “COMPONENT/RGB-IN SELECT” setting in the “SET UP” menu to “COMPONENT” (when COMPONENT signal connection) or “RGB” (when RGB signal connection). (see page 39)

Signal Names for Mini D-sub 15P Connector

5 4 3 2 1

10

9

8

7

6

15

14

13

12

 

11

Pin Layout for PC Input Terminal

Pin No.

Signal Name

Pin No.

Signal Name

Pin No.

Signal Name

1

R (PR/CR)

6

GND (Ground)

11

NC (not connected)

2

G (Y)

7

GND (Ground)

12

SDA

3

B (PB/CB)

8

GND (Ground)

13

HD/SYNC

4

NC (not connected)

9

+5 V DC

14

VD

5

GND (Ground)

10

GND (Ground)

15

SCL

10

Image 10
Contents Model No. TH-50VX100U TH-65VX100U High Definition Custom Home Theater Plasma DisplayOperating Instructions EnglishRisk of Electric Shock Do not Open Important Safety Instructions Table of Contents Canadian Notice FCC CautionTrademark Credits Safety Precautions When using the Plasma DisplaySetup MaintenanceSafety Precautions / Maintenance AC Power Supply CordAccessories Supplied AccessoriesRemote Control Batteries AC cord fixing ConnectionsCable fixing band PC Input Terminals connection Signal Names for Mini D-sub 15P ConnectorConnections Serial Terminals connection With this set Signal names for D-sub 9P connectorCommand Communication parametersComponent / RGB connection Hdmi connectionDVD Connecting the plug to the Wall Outlet Power on / OFFConnecting the AC cord plug to the Plasma Display When first switching on the unitSelecting the On-Screen Menu Language Selecting the input signalInitial selections OSD LanguageBasic Controls INPUT1, INPUT2, INPUT3Basic Controls Scrolling BAR and Test Patterns functions EXT. Scaler functionZoom Full Just All Aspect modeAspect Controls Fill Zoom Full JustSet Exit the menu SET UP POS. /SIZE SoundOn-Screen Menu Displays SelectSee On-Screen Menu DisplaysOverview See page 23Display the menu screen Picture AdjustmentsUsing for menu display Picture MenuPicture Adjustments Extension AdjustmentBlack GammaVideo NR, Mosquito NR, Block NR OFF MIN Advanced MAX MID PulldownSelect the item and set Advanced NRPicture Profiles MEMORY1Entering profile names Saving profilesPicture Profiles Example Specifying MY PictureLoading profiles Editing profiles Deleting profiles Renaming profilesMemory Edit SettingsLocking profiles Memory SaveIsf Mode Off Isf Mode On Isf Mode SettingPicture menu mode display Mode display when is selectedDisplay the menu screen Select POS. /SIZE Adjusting POS. /SIZEAuto Setup POSPixel Mode 2k1k Adjusting POS. /SIZEClock Phase DOT Clock During COMPONENT, RGB and PC input signalSound Adjustment Display the menu screen Select SoundScreensaver For preventing image retention Display the menu screen Select SET UPStart setting Select ScreensaverScreensaver For preventing image retention Adjust the menuReduces screen image retention Select Wobbling or Peak LimitSIZE, V-SIZE, 11 Pixel MODE, Display Size Select External Scaler Mode and setSpecifying the scaler BRIGHTNESS, COLOR, TINT, SharpnessPower Save Standby Save Reduces power consumptionAuto Power OFF Specify the display position Customizing the On-Screen Menu DisplaySpecify the background color TYPE1 TYPE2Select Component / RGB-IN Select and set SET UP for Input SignalsSelect YUV / RGB-IN Select and set For RGB Signal menuSET UP for Input Signals For ComponentAuto on G VBS Input signal displaySetting RGB sync signal OFF onSelect Options Options AdjustmentsPress for more than 3 seconds Select the input mode. see Select the remote control modeWatching Videos and DVDs Operate the connected equipment, pointing Display’s remoteWatching Videos and DVDs Troubleshooting Plasma Display panelList of Aspect Modes FullRemote Control Operation / Code List Remote Control Operation ListRemote Control Operation / Code List Remote Control Code ListDVD Recorder / Player Applicable Input Signals Video input Hdmi Applicable Input SignalsVGA60 Specifications Power ConsumptionPanasonic Professional Flat Panel Display Limited Warranty For the U.S.A and Puerto RicoLimited Warranty Statement For CanadaPage Executive Office Customer’s RecordPanasonic Professional Display Company Panasonic Canada Inc