Panasonic TQBC2372-1 manual Connections, AC cord fixing, Cable fixing band

Page 9

Connections

When connecting the speakers, be sure to use only the optional accessory speakers. Refer to the speaker’s Installation Manual for details on speaker installation.

Speaker terminal (L)

	Speaker
	Speaker		AC cord connection (see page 13)
	terminal (R)		AC cord connection (see page 13)
	terminal (R)	– AC cord fixing
		– AC cord fixing

1
2	1
	1
	2

1

2

Note:

Make sure that the AC cord is locked on both the left and right sides.

1Plug the AC cord into the display unit.

Plug the AC cord until it clicks.

2Fix the AC cord with the clamper which is attached to the unit.

Close

Push until the hook clicks.

Open

2. Pull off.

1. Keep the knob pressed.

Unplug the AC cord

Unplug the AC cord pressing the two knobs.

Note:

When disconnecting the AC cord, be absolutely sure to disconnect the AC cord plug at the socket outlet first.

–Cable fixing band

Secure any excess cables with band as required.

Note:

One fixing band is supplied with this unit. In case of securing cables at two positions, please purchase it separately.

Pass the attached cable fixing band through the clip as shown in the figure.

1

To secure cables connected to Terminals, wrap the cable fixing band around them then pass the pointed end through the locking block, as shown in the figure.

While ensuring there is sufficient slack in cables to minimize stress (especially in the power cord), firmly bind all cables with the supplied fixing band.

To tighten:	To loosen:
	Push the catch
Pull
2	Pull

	R	AUDIO L	PR/CR/R PB/CB/B	Y/G		AUDIO
		COMPONENT/RGB IN				AUDIO
		COMPONENT/RGB IN
SLOT1	SLOT2		SLOT3	PC	IN	SERIAL

Dual HDMI Terminals (equivalent		COMPONENT/RGB IN and		From EXTERNAL
of Dual HDMI Terminal Board		Audio IN Terminals (equivalent		monitor terminal
(TY-FB10HMD))		of RCA Component Video		on Computer
(see page 12)		Terminal Board (TY-42TM6Z))		(see page 10)
		(see page 12)
		(see page 12)

Note: At factory shipment, Terminal boards are installed in SLOT 1, SLOT 2 and SLOT 3.

From SERIAL Terminal on Computer (see page 11)

9

Image 9

Contents Operating Instructions High Definition Custom Home Theater Plasma DisplayModel No. TH-50VX100U TH-65VX100U EnglishRisk of Electric Shock Do not Open Important Safety Instructions Table of Contents FCC Caution Canadian NoticeTrademark Credits When using the Plasma Display Safety PrecautionsSafety Precautions / Maintenance MaintenanceSetup AC Power Supply CordAccessories Accessories SuppliedRemote Control Batteries Connections AC cord fixingCable fixing band Signal Names for Mini D-sub 15P Connector PC Input Terminals connectionConnections Command With this set Signal names for D-sub 9P connectorSerial Terminals connection Communication parametersHdmi connection Component / RGB connectionDVD Connecting the AC cord plug to the Plasma Display Power on / OFFConnecting the plug to the Wall Outlet When first switching on the unitInitial selections Selecting the input signalSelecting the On-Screen Menu Language OSD LanguageINPUT1, INPUT2, INPUT3 Basic ControlsBasic Controls EXT. Scaler function Scrolling BAR and Test Patterns functionsAspect Controls All Aspect modeZoom Full Just Fill Zoom Full JustOn-Screen Menu Displays SET UP POS. /SIZE SoundSet Exit the menu SelectOverview On-Screen Menu DisplaysSee See page 23Using for menu display Picture AdjustmentsDisplay the menu screen Picture MenuPicture Adjustments Black AdjustmentExtension GammaSelect the item and set PulldownVideo NR, Mosquito NR, Block NR OFF MIN Advanced MAX MID Advanced NRMEMORY1 Picture ProfilesPicture Profiles Saving profilesEntering profile names Example Specifying MY PictureLoading profiles Deleting profiles Renaming profiles Editing profilesLocking profiles SettingsMemory Edit Memory SavePicture menu mode display Isf Mode SettingIsf Mode Off Isf Mode On Mode display when is selectedAuto Setup Adjusting POS. /SIZEDisplay the menu screen Select POS. /SIZE POSClock Phase Adjusting POS. /SIZEPixel Mode 2k1k DOT Clock During COMPONENT, RGB and PC input signalDisplay the menu screen Select Sound Sound AdjustmentStart setting Display the menu screen Select SET UPScreensaver For preventing image retention Select ScreensaverReduces screen image retention Adjust the menuScreensaver For preventing image retention Select Wobbling or Peak LimitSpecifying the scaler Select External Scaler Mode and setSIZE, V-SIZE, 11 Pixel MODE, Display Size BRIGHTNESS, COLOR, TINT, SharpnessReduces power consumption Power Save Standby SaveAuto Power OFF Specify the background color Customizing the On-Screen Menu DisplaySpecify the display position TYPE1 TYPE2SET UP for Input Signals Select Component / RGB-IN Select and setSelect YUV / RGB-IN Select and set SET UP for Input Signals Signal menuFor RGB For ComponentSetting RGB sync signal Input signal displayAuto on G VBS OFF onOptions Adjustments Select OptionsPress for more than 3 seconds Watching Videos and DVDs Select the remote control modeSelect the input mode. see Operate the connected equipment, pointing Display’s remoteWatching Videos and DVDs Plasma Display panel TroubleshootingFull List of Aspect ModesRemote Control Operation List Remote Control Operation / Code ListRemote Control Code List Remote Control Operation / Code ListDVD Recorder / Player Applicable Input Signals Applicable Input Signals Video input HdmiVGA60 Power Consumption SpecificationsFor the U.S.A and Puerto Rico Panasonic Professional Flat Panel Display Limited WarrantyFor Canada Limited Warranty StatementPage Panasonic Professional Display Company Customer’s RecordExecutive Office Panasonic Canada Inc