Panasonic TH-50PH11UK, TH-42PH11UK manual PC Input Terminals connection, Connections

Page 10

Connections

PC Input Terminals connection

COMPUTER

Conversion adapter (if necessary)

(Female)

AUDIO

PC IN

Mini D-sub 15p

RGB

PC cable

(Male)

Audio

Stereo plug

Connect a cable which matches

the audio output terminal on the computer.

Notes:

•Computer signals which can be input are those with a horizontal scanning frequency of 15 to 110 kHz and vertical scanning frequency of 48 to 120 Hz. (However, the image will not be displayed properly if the signals exceed 1,200 lines.)

•The display resolution is a maximum of 768 × 768 dots (TH-42PH11UK), 1,024 × 768 dots (TH-50PH11UK) when the aspect mode is set to “4:3”, and 1,024 × 768 dots (TH-42PH11UK), 1,366 × 768 dots (TH-50PH11UK) when the aspect mode is set to “FULL”. If the display resolution exceeds these maximums, it may not be possible to show ﬁne detail with sufﬁcient clarity.

•The PC input terminals are DDC2B-compatible. If the computer being connected is not DDC2B-compatible, you will need to make setting changes to the computer at the time of connection.

•Some PC models cannot be connected to the set.

•There is no need to use an adapter for computers with DOS/V compatible Mini D-sub 15P terminal.

•The computer shown in the illustration is for example purposes only.

•Additional equipment and cables shown are not supplied with this set.

•Do not set the horizontal and vertical scanning frequencies for PC signals which are above or below the speciﬁed frequency range.

•Component Input is possible with the pin 1, 2, 3 of the Mini D-sub 15P Connector.

•Change the “COMPONENT/RGB-IN SELECT” setting in the “SET UP” menu to “COMPONENT” (when COMPONENT signal connection) or “RGB” (when RGB signal connection). (see page 34)

Signal Names for Mini D-sub 15P Connector

5 4 3 2 1

10		9		8	7	6
15	14		13	12		11

Pin Layout for PC Input Terminal

Pin No.	Signal Name	Pin No.	Signal Name	Pin No.	Signal Name
1	R (PR/CR)	6	GND (Ground)	11	NC (not connected)
2	G (Y)	7	GND (Ground)	12	SDA
3	B (PB/CB)	8	GND (Ground)	13	HD/SYNC
4	NC (not connected)	9	+5 V DC	14	VD
5	GND (Ground)	10	GND (Ground)	15	SCL

10

Image 10

Contents English Español Operating Instructions Manual de instruccionesModel No. Número de modelo Risk of Electric Shock Do not Open Important Safety Instructions Table of Contents Canadian Notice FCC CautionTrademark Credits Safety Precautions When using the Plasma DisplaySetup MaintenanceSafety Precautions / Maintenance AC Power Supply CordAccessories Supplied AccessoriesRemote Control Batteries Cable ﬁxing band ConnectionsAC cord ﬁxing SeePC Input Terminals connection Signal Names for Mini D-sub 15P ConnectorConnections Serial Terminals connection Signal names for D-sub 9P connectorCommand Communication parametersRCA-BNC Hdmi connectionComponent / RGB connection DVDConnecting the AC cord plug to the Plasma Display Power on / OFFConnecting the plug to the Wall Outlet Present Time Setup Power on / OFFWhen ﬁrst switching on the unit OSD LanguageSelecting the On-Screen Menu Language Selecting the input signalInitial selections INPUT1 INPUT2A INPUT2B INPUT3 PCBasic Controls Remote control sensor Volume AdjustmentMain Power On / Off Switch Power Indicator Menu Screen on / OFFBasic Controls On OFFAspect Controls All Aspect modePanasonic Auto Multi PIP Aspect ControlsAdvanced PIP Position Digital ZoomDisplay the operation guide Select the magniﬁcation required for the enlarged displayOn-Screen Menu Display Adjusting POS. /SIZE Dynamic Picture AdjustmentsStandard CinemaAdvanced Settings Picture AdjustmentsPress to exit from adjust mode Sound AdjustmentSDI Sound Output Present Time Setup SET UP TimerScreensaver For preventing image retention Setup of Screensaver TimeStart setting Function selectionScreensaver For preventing image retention Side BAR AdjustReduces screen image retention OFF Dark MID BrightReduces power consumption Addition sign Selected Input Customizing the Input labelsLandscape Portrait OFF SET UP for Multi DisplayHow to setup Multi Display Display Number locations for each arrangement ExamplesID remote control button operation ID Remote Control FunctionSET UP for Multi Display ID CancellationComponent / RGB in Select SET UP for Input SignalsYUV / RGB in Select SET UP for Input Signals Signal menu3D Y/C Filter For Ntsc AV images Color System / Panasonic Auto XGA ModeMode Function PulldownNoise Reduction Press to adjustRefresh Rate Advanced NRSetting RGB sync signal Input signal displaySync Options Adjustments INPUT1 INPUT2 INPUT3Options Adjustments MENU&ENTERNormalization 43→H-FILL→ZOOM→FULL→JUSTProgram number Weekly Command TimerPress Action button Program Edit screenShipping condition Press to select Time / CommandTime Set the time to execute a command program Press to set each itemTroubleshooting Plasma Display panelList of Aspect Modes FullVIDEO/COMPONENT/RGB/PC input signals Video input HdmiCommand list of Weekly Command Timer Speciﬁcations TH-42PH11UK TH-50PH11UKPanasonic Professional Flat Panel Display Limited Warranty For the U.S.ALimited Warranty Statement For CanadaPage Page Page Page Page Page Page Executive Ofﬁce Customer’s RecordPanasonic Professional Display Company Panasonic Canada Inc