Panasonic TH-32LHD7UY manual Accessories Supplied, Remote Control Batteries

Page 8

Accessories

Accessories Supplied

Check that you have the Accessories and items shown

Operating Instruction book

Remote Control

Transmitter

EUR646535

INPUT

SURROUND

VOL

Batteries for the

 

Warranty

 

Remote Control

Transmitter

(AA Battery × 2)

N

 

R

PICTURE

SOUND

SET UP

MULTI

 

ZOOM

PIP

SWAP SELECT

MOVE

PICTURE

 

 

POS. /SIZE

 

ASPECT

PC

OFF TIMER

DISPLAY

Ferrite core (Small size) × 2

Ferrite core

 

 

Fixing bands × 2

 

AC cord

(Large size)

× 2

 

 

 

 

 

 

 

 

Remote Control Batteries

Requires two AA batteries.

 

 

 

 

 

 

 

1. Turn the transmitter face down.

2. Install the batteries as shown in the

Press and slide off the battery

battery compartment.

cover.

(Polarity + or – must match the

 

markings in the compartment.)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3.Replace the cover and slide in reverse until the lock snaps.

Two “AA” size

Helpful Hint:

For frequent remote control users, replace old batteries with Alkaline batteries for longer life.

Precaution on battery use

Incorrect installation can cause battery leakage and corrosion that will damage the remote control transmitter. Disposal of batteries should be in an environment-friendly manner.

Observe the following precautions:

1.Batteries should always be replaced as a pair. Always use new batteries when replacing the old set.

2.Do not combine a used battery with a new one.

3.Do not mix battery types (example: “Zinc Carbon” with “Alkaline”).

4.Do not attempt to charge, short-circuit, disassemble, heat or burn used batteries.

5.Battery replacement is necessary when the remote control acts sporadically or stops operating the LCD Display.

8

Image 8
Contents English LCD Display Model No. TH-32LHD7UYOperating Instructions Risk of Electric Shock Do not Open Important Safety Instructions Table of Contents Trademark Credits FCC CautionCanadian Notice Safety Precautions When using the LCD DisplayIf problems occur during use SetupAC Power Supply Cord Remote Control Batteries AccessoriesAccessories Supplied AC cord fixing ConnectionsSpeakers Signal Names for D-sub 15P Connector PC Input Terminals connectionInstalling the ferrite core Large size CommandSerial Terminals connection Communication parametersRGB signal R, G, B, HD, VD AV & Component connectionConnecting the plug to the Wall Outlet Power on / OFFConnecting the AC cord plug to the LCD Display Basic Controls On OFF To Picture adjust menu see On-Screen Menu DisplaysTime / Power OFF Time On-Screen Menu DisplaysSelecting the input signal Initial selectionsSelecting the On-Screen Menu Language INPUT1 INPUT2 PCNormal Full Aspect ControlsNormal Zoom Full Adjusting Picture Position / Size Clock PhaseClock Phase RGB/PC in modeMulti PIP Picture Adjustments AutoStandard DynamicAdvanced Settings Sound Adjustment MuteBass TrebleDigital Zoom Display the Operation GuideSelect the area of the image to be enlarged Select the magnification required for the enlarged displayPresent Time Setup / SET UP Timer Present Time SetupSET UP Timer Power on Time / Power OFF TimeCustomizing the Input labels Reduces power consumptionPower Save Standby Save Power Management Auto Power OFF SET UP for Input Signals Component / RGB in Select3D Y/C Filter For Ntsc AV images SelectColor System Color System / Panasonic AutoPulldown / Video NR Setting RGB sync signal SyncFREQ. kHz / V-FREQ. Hz Displays the H Horizontal / V Vertical frequenciesShipping condition Troubleshooting LCD Display panelVIDEO/COMPONENT/RGB/PC input signals Video input Applicable when Multi Screen and Digital ZoomApplicable input signals for PC Input D-sub 15P ∗ Mark PAL60Accessories Supplied SpecificationsCustomer’s Record Panasonic Broadcast & Television Systems CompanyExecutive Office Panasonic Canada Inc