Panasonic TH-32LHD7UY manual Connections, Speakers, AC cord ﬁxing

Page 9

Connections

When connecting the speakers, be sure to use only the optional accessory speakers. Refer to the speaker’s Installation Manual for details on speaker installation.

Speakers (Optional accessories)

	AV	SPEAKERS
SLOT 1	SLOT 2PC INSERIAL	SPEAKERS

		Terminals (L)
	SPEAKERS	AC cord connection (see page 13)
	Terminals (R)	AC cord connection (see page 13)
	Terminals (R)
		– AC cord ﬁxing

1
2	1
	1
	2

1.Open the clamper.

Clamper

2. Insert the AC cord	3. Slide up the clamper and ﬁx	4. Insert the point of the
and close the clamper	the AC cord plug securely.	ﬁxed clamper into the
securely.	When loosen	small hole on the lower
	the clamper:	r i g h t	o f
		the back
		cover	as
		necessary.

AC cord

Note: The power plug in the illustration may not be the type ﬁtted to your set.

–Cable ﬁxing bands

Secure any excess cables with bands as required.

Pass the attached cable ﬁxing band through the clip as shown in the ﬁgure.

To secure cables connected to Terminals, wrap the cable ﬁxing band around them then pass the pointed end through the locking block, as shown in the ﬁgure.

While ensuring there is sufﬁcient slack in cables to minimize stress (especially in the power cord), ﬁrmly bind all cables with the supplied ﬁxing band.

To tighten:	To loosen:
	Push the catch

Pull

1

2

Pull

R

AUDIO

L

VIDEO IN

VIDEO OUT

R

AUDIO

L

VD

HD

PR/CR/R PB/CB/B

Y/G

AUDIO

IN

S VIDEO IN

AV

COMPONENT/RGB IN

SLOT1

SLOT2

PC

IN

SERIAL

AV Terminals (see page 12)

COMPONENT/RGB IN and Audio IN Terminals (see page 12)

From EXTERNAL monitor terminal on Computer (see page 10)

From SERIAL Terminal on Computer (see page 11)

Note: At factory shipment, Terminal boards are installed in SLOT 1 and SLOT 2.

9

Image 9

Contents LCD Display Model No. TH-32LHD7UY Operating InstructionsEnglish Risk of Electric Shock Do not Open Important Safety Instructions Table of Contents FCC Caution Canadian NoticeTrademark Credits When using the LCD Display Safety PrecautionsSetup AC Power Supply CordIf problems occur during use Accessories Accessories SuppliedRemote Control Batteries Connections SpeakersAC cord ﬁxing PC Input Terminals connection Signal Names for D-sub 15P ConnectorCommand Installing the ferrite core Large sizeSerial Terminals connection Communication parametersAV & Component connection RGB signal R, G, B, HD, VDPower on / OFF Connecting the AC cord plug to the LCD DisplayConnecting the plug to the Wall Outlet Basic Controls On OFF On-Screen Menu Displays To Picture adjust menu seeOn-Screen Menu Displays Time / Power OFF TimeInitial selections Selecting the input signalSelecting the On-Screen Menu Language INPUT1 INPUT2 PCAspect Controls Normal Zoom FullNormal Full Clock Phase Adjusting Picture Position / SizeClock Phase RGB/PC in modeMulti PIP Auto Picture AdjustmentsStandard DynamicAdvanced Settings Mute Sound AdjustmentBass TrebleDisplay the Operation Guide Digital ZoomSelect the area of the image to be enlarged Select the magniﬁcation required for the enlarged displayPresent Time Setup Present Time Setup / SET UP TimerPower on Time / Power OFF Time SET UP TimerReduces power consumption Power Save Standby Save Power Management Auto Power OFFCustomizing the Input labels Component / RGB in Select SET UP for Input Signals3D Y/C Filter For Ntsc AV images SelectColor System / Panasonic Auto Pulldown / Video NRColor System Sync Setting RGB sync signalFREQ. kHz / V-FREQ. Hz Displays the H Horizontal / V Vertical frequenciesShipping condition LCD Display panel TroubleshootingVideo input Applicable when Multi Screen and Digital Zoom VIDEO/COMPONENT/RGB/PC input signalsApplicable input signals for PC Input D-sub 15P ∗ Mark PAL60Speciﬁcations Accessories SuppliedPanasonic Broadcast & Television Systems Company Customer’s RecordExecutive Ofﬁce Panasonic Canada Inc