Panasonic TH-32LHD7UY manual Serial Terminals connection, Installing the ferrite core Large size

Page 11

Connections

SERIAL Terminals connection

The SERIAL terminal is used when the LCD Display is controlled by a computer.

COMPUTER

 

Ferrite core

 

RS-232C

(large size)

 

SERIAL

Straight cable

(supplied)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

D-sub 9p

Less than 3” 15/16

 

(10 cm)

Notes:

Use the RS-232C cable to connect the computer to the LCD Display.

The computer shown is for example purposes only.

Additional equipment and cables shown are not supplied with this set.

6 7 8 9

1 2 3 4 5

Pin layout for RS-232C

Installing the ferrite core (Large size)

Open

The SERIAL terminal conforms to the RS-232C interface specification, so that the LCD Display can be controlled by a computer which is connected to this terminal.

The computer will require software which allows the sending and receiving of control data which satisfies the conditions given below. Use a computer application such as programming language software. Refer to the documentation for the computer application for details.

Communication parameters

Signal level

RS-232C compliant

Synchronization method

Asynchronous

Baud rate

9600 bps

Parity

None

Character length

8 bits

Stop bit

1 bit

Flow control

-

RS-232C Conversion cable

D-sub 9-pin female

Details

 

2

R X D

 

3

T X D

 

5

GND

4

• 6

Non use

 

7

Shorted

 

8

 

 

1

• 9

NC

Basic format for control data

The transmission of control data from the computer starts with a STX signal, followed by the command, the parameters, and lastly an ETX signal in that order. If there are no parameters, then the parameter signal does not need to be sent.

STX C1 C2 C3 : P1 P2 P3 P4 P5 ETX

 

Colon

Parameter(s)

End

Start

3-character

(1 - 5 bytes)

(03h)

(02h)

command (3 bytes)

 

 

Notes:

If multiple commands are transmitted, be sure to wait for the response for the first command to come from this unit before sending the next command.

If an incorrect command is sent by mistake, this unit will send an “ER401” command back to the computer.

Command

Command

Parameter

Control details

PON

None

Power ON

POF

None

Power OFF

AVL

**

Volume 00 - 63

AMT

0

Audio MUTE OFF

1

Audio MUTE ON

 

IMS

None

Input select (toggle)

 

SL1

Slot1 input

 

SL2

Slot2 input

 

PC1

PC input

DAM

None

Screen mode select (toggle)

 

NORM

NORMAL (4 : 3)

 

ZOOM

ZOOM

 

FULL

FULL

 

JUST

JUST

 

SELF

Panasonic AUTO

With the power off, this display responds to PON command only.

11

Image 11
Contents English LCD Display Model No. TH-32LHD7UYOperating Instructions Risk of Electric Shock Do not Open Important Safety Instructions Table of Contents Trademark Credits FCC CautionCanadian Notice When using the LCD Display Safety PrecautionsIf problems occur during use SetupAC Power Supply Cord Remote Control Batteries AccessoriesAccessories Supplied AC cord fixing ConnectionsSpeakers PC Input Terminals connection Signal Names for D-sub 15P ConnectorCommunication parameters Installing the ferrite core Large sizeCommand Serial Terminals connectionAV & Component connection RGB signal R, G, B, HD, VDConnecting the plug to the Wall Outlet Power on / OFFConnecting the AC cord plug to the LCD Display Basic Controls On OFF On-Screen Menu Displays To Picture adjust menu seeOn-Screen Menu Displays Time / Power OFF TimeINPUT1 INPUT2 PC Selecting the input signalInitial selections Selecting the On-Screen Menu LanguageNormal Full Aspect ControlsNormal Zoom Full RGB/PC in mode Adjusting Picture Position / SizeClock Phase Clock PhaseMulti PIP Dynamic Picture AdjustmentsAuto StandardAdvanced Settings Treble Sound AdjustmentMute BassSelect the magnification required for the enlarged display Digital ZoomDisplay the Operation Guide Select the area of the image to be enlargedPresent Time Setup Present Time Setup / SET UP TimerPower on Time / Power OFF Time SET UP TimerCustomizing the Input labels Reduces power consumptionPower Save Standby Save Power Management Auto Power OFF Select SET UP for Input SignalsComponent / RGB in Select 3D Y/C Filter For Ntsc AV imagesColor System Color System / Panasonic AutoPulldown / Video NR Displays the H Horizontal / V Vertical frequencies Setting RGB sync signalSync FREQ. kHz / V-FREQ. HzShipping condition LCD Display panel TroubleshootingPAL60 VIDEO/COMPONENT/RGB/PC input signalsVideo input Applicable when Multi Screen and Digital Zoom Applicable input signals for PC Input D-sub 15P ∗ MarkSpecifications Accessories SuppliedPanasonic Canada Inc Customer’s RecordPanasonic Broadcast & Television Systems Company Executive Office