Code Programming | Panasonic NV-FJ720 specification

CH DATE ON OFF

2 27SA 1 3 : 4 5 1 4 : 1 5 SP

G-Code Programming

Programming is now easier than ever; simply enter the G-Code number found in the programme scheduling pages of newspapers and magazines.

G-Code numbers are numbers assigned to programmes listed in the TV programme schedule found in newspapers and TV guides. When these numbers are entered, the numbers are converted to actual programming.

G-CODEis a trademark of Gemstar Development Corporation. The G-CODEsystem is manufactured under licence from Gemstar Development Corporation.

Preparations

–Confirm that the VCR is on.

–Confirm that the TV is on and the VCR viewing channel is selected.

–Insert a video cassette with an intact erasure prevention tab.

–Set the VCR/TV switch E to [VCR].

–Check that the clock is set to the correct time. If it has not been set, refer to page 10.

Example:

Programming a timer recording of a TV programme with the G-Code number 123456

4Press the Cursor button (1) S to select the Category.

Then, select the desired category by pressing the Cursor buttons (3421) S.

CATEGORY SETTING		CATEGORY SETTING
≥MOVIE	≥SPORT	≥MOVIE	≥SPORT
≥MUSIC	≥CHILD	≥MUSIC	≥CHILD
≥DRAMA	≥NEWS	≥DRAMA	≥NEWS
≥EDUCA	≥OTHER	≥EDUCA	≥OTHER
≥DOCUM	≥– – – – –	≥DOCUM	≥– – – – –
	END : MENU		END : MENU

–Alternatively, you can set the category on the Navigator list. (See page 23 for details.)

–This function is activated when [JET NAVIGATOR] is set to [ON]. (See page 13.) When [JET NAVIGATOR] is set to [OFF], procced to the step 6.

5Press the MENU button U to make the previous display appear.

CH	DATE ON	OFF
2	27SA 1 3 : 4 5	1 4 :	1 5 SP

CHECK : PROG./CHECK

6 Press the TIMER (REC) button A to switch the VCR

over to the timer recording standby mode.

– When [JET NAVIGATOR] is set to [ON], the

[PROGRAMME IS COMPLETE. REMAINING

PROGRAMME 49.] message appers. (See page 13.)

– When [JET NAVIGATOR] is set to [OFF], the

Operations

1Press the G-CODE/SV button H to display the menu for entering the G-Code number on the TV.

2Press the Numeric buttons 2 to enter the G-Code number.

On Screen Display

G-CODE

---------

END:G-CODE

G-CODE

123456---

[PROGRAMME IS COMPLETE.] message appears.

(See page 13.)

– Check that [Á] is lit on the VCR display.

If it is flashing, check the timer recording details again.

(See page 21.)

Notes:

– When the G-Code number is used for programming, the

recording time may be slightly longer than the actual

programme time.

–It is also possible to check the

number with VCR display without	PROGRAMME SET :OK
number with VCR display without	END:G-CODE
appearing the On Screen Display.

–If you have entered the wrong number, press the CANCEL button ; then enter the proper number. An alternative method is to press the Cursor button (2) S and then enter the proper number.

3Press the OK button T.

–The entered programme appears on the display.

– The starting time and the ending time appears alternately each

5 seconds on the VCR display.

SP ON

–Confirm that the number corresponds to the right

programme. If the display looks like this and Á on the VCR display flashes on and off: select the desired programme position using the Channel button 9, then press the OK button T.

–To make any corrections, use the DATE button :, the ON button D, the OFF button C and the SPEED button B the same way as described on page 19.

– Repeat steps 2 and 3 if [PROGRAMME IS INCOMPLETE.]

appears.

– When programming two or more programmes, repeat

steps 1 –6.

– The procedures for checking and cancelling a timer

programme are the same as on page 21.

To Suspend the Timer Recording Standby Mode

See page 20.