Panasonic CT-2701 Connection to Other Equipment, Setting Language, TV Operation, Press Action

CONNECTION TO OTHER EQUIPMENT (CONTINUED)

4.To connect the TV to a VCR with an S-VIDEO jack Set the TV/AV selection for this connection, to AUX1.

If you connect a VCR with an S-video cable to the S-VIDEO jack on the rear of TV, you must also connect the audio cables to the AUDIO IN jacks on the rear of the TV. The S-video cable only carries the video signal. Audio signal is separate.

VCR	Rear of TV
	IN	OUT
	VIDEO	VIDEO
	ANT(75 ) L/MONO	L/MONO
	S-VIDEO

AUDIO AUDIO

R R

AUDIO (L)

(not supplied) AUDIO (R)

(not supplied)

SETTING LANGUAGE

NOTE: When the S-video cable and the video cable are connected to each jack at the same time, the S-video cable takes precedence over the video cable.

ENGLISH

This TV can display the channel number, on screen displays and picture adjustments on the screen in English, Spanish or French.

1	Press ACTION.
2	Press B to select the SET UP
	mode, then press ACTION.

NOTE:

All four arrows can be used to select the SET UP mode, not just B.

SETPICTUREUP	AUDIO	TIMER
	EXIT
LOCK		SET UP
LANGUAGE/IDIOMA/LANGUEANUALODEAUTOCCPROGRAM/ACTION:FF:CABLEGRAM

3	Press and then press ▲ or ▼ to	LANGUAGE/IDIOMA/LANGUE
	select desired language (e.g.
	English), then press ACTION.	ENGLISH
		ESPAÑOL
		FRANÇAIS

/ /ACTION

4 Press ACTION to select the EXIT mode, then press ACTION again.

NOTE:

If Spanish or French is chosen, the Closed Caption indicators will be in the selected language, but the Closed Caption text will not be affected by the language selection.

TV OPERATION

1 To turn on the TV, press POWER.

2 The VOLUME can be adjusted to a desired level by pressing VOL (VOLUME) B or A .

The sound level will be indicated on the TV screen by GREEN BARS AND A NUMBER. As the sound level increases, so do the number of BARS AND THE NUMBER on the screen. The same is true for decreasing the level.

3	Set the TV/CATV menu option to the appropriate position.
	When shipped from the factory, this menu option is in the
	CATV setting. See "To Memorize Channels".
	TV	-	VHF/UHF channels
	CABLE	-	CABLE TV channels
4	CH (CHANNEL) ▲ and ▼

Press and release the CH (CHANNEL) ▲ or ▼ . The channel automatically stops at the next channel set into memory. Press and hold the button down to change channels more quickly.

For proper operation, before selecting channels, they should be set into the TV's memory. See "To Memorize Channels".

DIRECT CHANNEL SELECTION (0-9) - Press these buttons to select a channel.The channel number will appear on the upper right corner of the TV screen. If an invalid channel number is selected, the display will revert to the previous channel.

TV MODE DIRECT CHANNEL SELECTION - When the TV/ CATV menu option is in the TV position, all channels can be instantly selected by using two buttons (For example, to select channel 2, press "0", then "2". If you press only "2", channel selection will be delayed for a few seconds). For channels 10 and above, press the 2 digits in order.

CATV mode direct channel selection

When the TV/CATV menu option is in the CATV position, channels can be selected as follows:

1-9	Press "0" twice, then 1-9 as needed.
	Example, to select channel 2, press "002".
10-12	Press "0", then remaining 2 digits.
	Example, to select channel 12, press "012".
13-99	Press the 2 digits in order.
	Example, to select channel 36, press "36".
100-125	Press the 3 digits in order.
	Example, to select channel 120, press "120".

NOTE: If the station being viewed stops broadcasting, the TV will automatically shut off after 15 minutes.

7