Haier LCD-42K40-HD, LCD-42K40A-HD, LCD-32K40A owner manual Trouble Shooting, Power

Page 45

APPENDIX

TROUBLE SHOOTING

Before calling your dealer or service center for assistance, check the matters below once again.

1.Make sure you have connected LCD TV to your equipment as described in the section "CONNECTING LCD TV" .

2.Check cable connection. Verify that all external equipment and power cords are properly connected.

3.Verify that all power is switched on.

4.If LCD TV still does not produce an image, re-start the external equipment.

5.If the image still does not appear, unplug LCD TV from the external equipment and check the external equipment. The problem may be with your graphics controller rather than with LCD TV. (When you reconnect LCD TV, remember to turn the external equipment and TV off before you power up LCD TV. Power the equipment back on in order of : LCD TV and external equipment.)

6.If the problem still exists, check the following chart.

Problem:

Try these Solutions

 

 

NO

Plug this LCD TV into the AC outlet.

Press ON/STAND-BY button on SIDE Control or on Remote Control to open this LCD TV.

POWER

Check POWER Indicator. If this indicator flashes, LCD TV has any trouble.

Remote

● Check the batteries.

● Make sure nothing is between the Remote Receiver and the Remote Control.

Control

● Make sure you are not too far from LCD TV when using Remote Control.

does not

Maximum operating range is 16.4' (5m).

● Is direct sunlight or strong artificial light shining on LCD TV's Infrared Remote

work

Receiver? Eliminate the light by closing curtains, pointing the light in a different

 

direction, etc.

No image

Check the connection between the external equipment and LCD TV.

When turning LCD TV on, it takes a few seconds to display the image.

 

 

Check the system that you select is corresponding with the external equipment or the video

 

equipment.

 

Make sure the temperature is not out of the Operating Temperature (0°C ~ 40°C).

 

Turn off power, then turn on again, re-start LCD TV.

No sound

Check Audio cable connection from Audio input source.

Adjust the Audio source.

 

 

Press VOLUME (+) button.

 

Press MUTE button.

There are

 

tiny black

 

points

Dark or bright points of light (red, green, or blue) may appear on the screen. This is a

and/or

characteristic of the LCD panels, not a malfunction of the LCD TV.

bright

 

point on

 

the TV

 

Abnormal

● Adjust the value of colour.

colour of

● Select different colour system.

image

 

 

 

WARNING :

High voltages are used to operate this LCD TV. Do not attempt to open the cabinet.

If the problem still persists after following all operating instructions, contact the sales dealer where you purchased LCD TV or the service center. Give the model number and explain the difficulty. We will advise you how to obtain service.

45

LCD-K40.indd 45

1/21/2010 10:47:31 AM

Image 45
Contents Model LCD-32K40 LCD-32K40A LCD-42K40-HD LCD-42K40A-HD LCD TVImportant Information To the Owner Safety PrecautionLCD TV Safety InstructionsConnecting AC Power Cord Channel Text Blue Installing StandSurround Uninstalling Stand Base Sound Mode Picture Mode Still Wide Sports Mode OFF TimerFeature and Design Part Names and Functions PreparationPreparation Connecting LCD TV Installing StandConnecting AC Power Cord Connecting Outdoor Aerial Connecting a ComputerMAC HDMI2 HDMI4 DVI Connecting Video EquipmentBefore Operation Operation of Remote ControlOperation Range Remote Control Batteries InstallationON-SCREEN Menu TV/AV/HDMI Mode Menu ListTimer Menu PC Mode Menu List Basic Operation Power onTurning on / OFF LCD TV Plug & PlayChannel Recall Selecting Input SourceChannel Selection Channel UPInfo Volume ControlMute ECOPicture Mode Sound ModeStill Standard News Music PersonalFull WideSports Mode OFF TimerOFF Football Winter Sports Marine Sports Indoor Sports AV1 Auto Game Game ModePIP ON/OFF PIP/POP OperationPOP ON/OFF Xacti button Redw button Greent button Xacti LinkHDMI4 USBOperation of Remote Control in Text Mode TEXT/ TV Text CancelText Reveal Text IndexText Hold Text SizeText RED Text GreenChannel Menu ChannelAuto Search Menu SEMI-AUTO Search MenuManual Search Menu Menu Operation TV/AV/HDMI modePicture Menu PictureSound Menu SoundTimer Menu TimerOSD PersianOSD Menu Setup Menu SetupMode Hdmi LinkMenu Operation PC mode Menu Operation PC mode PC Adjust SetupDealer Mode Dealer ModeTo Display Dealer Mode Dealer Mode Cleaning LCD TV Function of Product Safety FeatureAppendix Power Trouble ShootingVesa Dpms Technical SpecificationsPAL/SECAM/NTSC/NTSC4.43 AV3VGA in D-SUB Terminal Configurations of VGA TerminalsXacti camera models with HDMI-CEC Uninstalling Stand Base LCD-K40.indd 21/2010 104740 AM Uninstalling the stand base is completed now Part No AA6P1P5823-- N7TK UE6-A