Sharp LC-32SH330E Use Sound Mode, Select a digital audio language, Automatically install channels

Page 14

TV menu

Use Sound Mode

Apart from manually adjusting sound settings, you can use Sound Mode to set your TV to a predefined sound setting.

1.Press MENU on the remote control and select Sound.

2.Press OK or ≥ to enter Sound and select

Sound Mode.

3.Press ≤≥ to select one of the following settings:

•Personal

•Music

•Speech

4.Follow the on-screen instructions to exit.

TV

The first time you set up your TV, you are prompted to select an appropriate menu language and to perform automatic installation of TV and digital radio channels (If available).

This chapter provides instructions on how to reinstall channels as well as other useful channel installation features.

NOTE

• Re-installing channels modifies the channel list.

Select a digital audio language

1.Press MENU on the remote control and select TV.

2.Press OK or ≥ to enter TV menu.

3.Press <> to select 1st Audio or 2nd Audio.

4.Highlight your selection and press ≤≥ to select an audio language.

5.Follow the on-screen instructions to exit.

NOTE

•If your selected audio language is not broadcasted, the default audio language will be displayed.

Automatically install channels

This section describes how to search and store channels automatically. Instructions are for both digital and analogue channels.

Step 1: Select your Tuner Mode

1.Press MENU on your remote control and select TV ≥ Tuner Mode.

2.Press ≤≥ to select Antenna or Cable.

3.Follow the on-screen instructions to exit.

Step 2: Select your country

Select the country where you are located. The TV installs and arranges channels according to your country.

1.Press MENU on the remote control and select TV ≥ Country.

2.Press ≤≥ to select your country.

3.Follow the on-screen instructions to exit.

Step 3: Automatic channel scan

Your TV searches and stores all available digital and analogue TV channels as well as all available digital radio channels.

1.Press MENU on the remote control and select TV ≥ Channels.

NOTE

•You are prompted to enter current password to enter

Channels if Channel Block /Parental Guidance /

Input Block in the Parental menu is not the default setting.

2.Select Channel Scan and press OK or ≥ and select ATV only or ATV and DTV to start channel installation. The installation may take a few minutes.

3.When complete, follow the on-screen instructions to exit.

EEUpdate Scan

Update Scan has similar function with Channel Scan. The difference is you could update channel list without erasing the original information.

NOTE

• This function is for Antenna mode only.

1.Press MENU on the remote control and select TV ≥ Channels.

NOTE

•You are prompted to enter current password to enter

Channels if Channel Block /Parental Guidance /

Input Block in the Parental menu is not the default setting.

2.Press <> to select Update Scan and press OK or ≥ to start channel update.

3.When complete, follow the on-screen instructions to exit.

13

Page 13 Page 15
Image 14
Page 13 Page 15
Contents LC-26SH330E / LC-32SH330E LC-42SH330EContents Introduction Important Safety PrecautionsPrecautions when transporting the TV Dear Sharp customerRemote control unit TV Front view RS232C-connectorRS232 connector is only used for service purpose TV Rear viewMount the TV base Supplied accessoriesPreparation Wall mountingSelect an item by the remote control Installation of batteriesUsing the remote control Display the Menu ScreenQuick guide Initial installation overviewPower on and run the auto installation PreparationTuner mode setting Watch TVWatching TV Standby modeTV indicator status Press EPG or Exit to exit Switch on EPGEPG Electronic Programme Guide Buttons for teletext operations Using the MHEG5 application UK onlyTeletext Select a Teletext languageSound TV menuPicture EEUpdate Scan Use Sound ModeAutomatically install channels Select a digital audio languageEEFavourite Network Select EESingle RF ScanMenu EEAnalogue Manual Scan EEChannel Edit EEChannel SkipEEChannel Sort Channel sort allows you to reorder the channelsFeatures Normal Not for HDWide Zoom 1 Not for HDZoom 2 Not for HD EESet analogue subtitles EEAutomatically switch the TV to standby Sleep timerUse subtitles EESelect a subtitle language on digital TV channelsDivX Setup EEDivX Registration VOD No Signal OffReset Default Hdmi overscanParental Repeat to 4 to change password Set / Change passwordClear all parental settings Reset all the settings in the Parental menuEEView Photos Connecting a USB deviceUSB function EEBasic OperationEEPlay Videos USB device compatibilityEEListen to Music YPbPr Component connection Connecting external devicesHdmi connection Scart connectionChecking CA module information Speaker / Amplifier connectionInserting the Smartcard into the CA module Analogue connection Connecting a PCVideo formats Appendix TroubleshootingProblem Possible Solution Hair dryersSpecification STEREO/BILINGUAL NICAM/A2Environmental specifications Other informationAcknowledgements TrademarksSoftware developed by Sharp and open source software Other Countries outside the EU Information on Disposal for Business Users European UnionPage Special Note for Users in the U.K Blue Neutral Brown Live
Top Page Image Contents