Sharp DV-RW370X operation manual Timer Recording cont’d, To stop the timer recording in progress

Recording

Timer Recording (cont’d)

Checking, cancelling, or correcting the timer programming information

In the following example, No.

5 timer programming overlaps on No. 1 and No. 6 timer programmes. In such a case, you should correct the programme time to clear the overlap.

		Timer Programming							VCR	DVD
		Date			Start	End	CH	DVD		Mode
								VCR
1.		01/01			12:00	13:00	P01	DVD		XP
2.		-	-	-
3.		-	-	-		Overlap
4.		-	-	-		No.1 6
	5.	01/01			12:30	14:00	P02	DVD		SP
6.		01/01			13:45	21:00	P12	DVD		SEP

7.- - -

8.- - -

1

Press [T-SET] so that the icon disappears from the front panel display.

2

Press [TIMER PROG.]. Timer Programming list will appear.

	Timer Programming
						VCR		DVD
	Date	Start	End	CH	DVD		Mode
					VCR
1. 01/01		12:00	13:00	P01	DVD			XP

2. - - -

3. - - -

4. - - -

5. - - -

6. - - -

7. - - -

8. - - -

3

Check the information on the list you will need.

4

To clear the timer program- ming, select the desired pro- gramme using [Cursor K / L], then press [CLEAR/C-RESET].

To correct the timer program- ming

1)Select the desired programme using [Cursor K / L], then press [ENTER].

2)Correct the timer programming using [Cursor K / L / { / B].

3)Press [ENTER] again.

5

Press [TIMER PROG.] to exit.

6

Press [T-SET] to return to the timer-standby mode.

To check the timer program- ming in process

Press [TIMER PROG.].

	OPERATE	DUBBING		SETUP	OPEN/CLOSE	2
					EJECT
1	T-SET	TIMER PROG. REC MODE			RAPID PLAY
	ZOOM		VCR	DVD	CM SKIP	5
6	TOP MENU				MENU LIST	6
	RETURN				ENTER
	.@/:		ABC	DEF
	1		2	3	PROG.
	GHI		JKL	MNO
	4		5	6
	PQRS		TUV	WXYZ
	7		8	9	SKIP
	CLEAR/C-RESET		SPACE	DISPLAY		4
			0
	REV				FWD
			PLAY
	VCR				DVD
	REC/OTR				REC/OTR
			STOP

Note

•If a timer recording is proceeding, that programme is highlighted in red. In such a case, you cannot select any other programmes.

•When you check the timer programming in progress by pressing [TIMER PROG.] during operations of the component (VCR or DVD) which is not currently used for the timer recording, the programme will not be highlighted. In this case, you cannot select other programmings.

To stop the timer recording in progress

Press [STOP C] to stop the disc recording or [STOP C/EJECT A] to stop the tape recording on the front panel of the unit.

Note

•[STOP C] on the remote control is not effective.

If the timer programming did not complete correctly

The error number appears on the Timer Programming list.

The error numbers indicate:

	Timer Programming					VCR	DVD
	Date	Start	End	CH	DVD		Mode
					VCR
* 01/01
		12:00	13:00	P01	DVD		E1
2.	- - -
3.	- - -

The error programme will be displayed in grey with an asterisk and have an error number.

The error programme will be deleted once you check the error in the programme list, or once you cancel the timer-standby mode and re-enter it.

Press [CLEAR/C-RESET] to erase the selected programme.

32 EN

E1-22	Recording error
E37-39
E23-24	Unrecordable disc
E25	• Copy prohibited programme
	• Cannot record because of the
	NTSC / PAL-60 signal is received.
E26-28	Copy prohibited programme
E29	Disc protected
E30	Disc full
E31	Already recorded 99 titles (Video
	mode)
E32	Already recorded 99 titles (VR
	mode)
E33	Already recorded 999 chapters

E34	No space for Control information
E35	PCA (Power Calibration Area) full
E36	Already finalised Video format disc
E40	• There are some unrecorded
	parts due the overlapped timer
	programmes.
	• Recording did not start at the
	start time.
	• There is no tape in the cassette
	compartment.
	• Tape recording reaches to
	the tape end during timer
	recording.
E41	Power failure
E42	No disc