Sharp LC-37G20S Initial auto installation, Checking signal strength and channel strength

Page 11

Quick guide

Initial auto installation

When the TV powers on for the first time after purchase, the initial auto installation wizard appears. Follow the menus and make the necessary settings one after another.

Confirm the following before turning on the power

E Is the antenna cable connected?

E Is the AC cord plugged in?

1 Press A on the TV.

The initial auto installation wizard appears.

2 Setting the on-screen display language

English

Italiano

Svenska

Press a/b/c/d to select the desired language, and then press OK.

3 Setting the country (Location of TV set screen)

Austria A B/G

Finland FIN B/G

Greece GR B/G

Press a/b/c/d to select your country or area, and then press OK.

The Location of TV set screen only appears during the first installation.

4 Starting channel search

Digital Search

Analogue Search

Press c/d to select “Digital Search” or “Analogue Search”, and then press OK.

If you want to search for more broadcasts, execute “Auto Installation” again from the Setup menu.

5 The TV searches for, sorts and stores all the receivable TV stations according to their settings and the connected antenna.

To abort the initial auto installation in progress, press END.

NOTE

If you turn off the power on the TV after performing step 4, the initial auto installation wizard does not appear. The auto installation function allows you to execute the installation again from the Setup menu. (Page 26)

The initial auto installation wizard will go off if you leave the TV unattended for 30 minutes before searching for channels in step 5.

Checking signal strength and channel strength

If you install a DVB-T antenna for the first time or relocate it, you should adjust the alignment of the antenna to receive a good reception while checking the antenna setup screen.

1 Press MENU and the menu screen displays.

2 Press c/d to select “Setup”.

3 Press a/b to select “Antenna Setup-DIGITAL”, and then press OK.

EChecking signal strength

Press a/b to select “Signal Strength”.

 

Supply Voltage

 

 

 

 

Signal Strength

 

 

 

 

Channel Strength

CH No.

21

 

 

 

Signal Strength

 

 

 

 

Current

0

Max.

0

 

Quality

 

 

 

 

Current

0

Max.

0

EChecking channel strength

Press a/b to select “Channel strength”, and then press OK.

You can input a specified frequency band using 0 - 9 numeric buttons.

Supply Voltage

2

6

5

.

2

 

Signal Strength

MHz

 

 

 

 

 

 

Channel Strength

CH No.

 

21

 

 

 

 

Signal Strength

 

 

 

 

 

Current

 

0

 

Max.

0

 

Quality

 

 

 

 

 

 

Current

 

0

 

Max.

0

4 Position and align the antenna so that the maximum possible values for “Signal Strength” and “Quality” are obtained.

NOTE

The values of “Signal Strength” and “Quality” indicate when to check the appropriate alignment of the antenna.



Image 11
Contents Español Nederlands Italiano Français Deutsch English Blue Neutral Brown Live Special Note for Users in the U.KContents Dear Sharp customer Important Safety PrecautionsPrecautions when transporting the TV IntroductionIntroduction Remote control unitTV Rear view Remote control sensor OPC sensorOPC indicator Sleep indicator Standby/On indicator TV Front viewAttaching the stand unit Supplied accessoriesPreparation Preparation Using the remote control unitInserting the batteries Quick guide Initial installation overviewCountry setting Channel search settingBundling the cables Before turning on the powerSupplying power to the antenna Setting the TV on the wallEChecking signal strength Initial auto installationChecking signal strength and channel strength Confirm the following before turning on the powerDaily operation Watching TVEPG Overview Useful settings for using EPGEPG Electronic Programme Guide Search a programme in a category Selecting a programme using EPGBasic Operation EDisplay the EPG screen Selecting a programme Check programme informationESelecting Record in the timer setup screen Timer recording using EPGCancelling the timer recording ESelecting Watch in the timer setup screenTeletext Using the MHEG5 application UK onlyIntroduction to connections Connecting external devicesEBefore connecting VIDEO/VIDEO connection Connecting external devicesEAfter connecting Hdmi Audio Select Hdmi connection C R Component connectionScart connection Controlling devices with Scart using AV LinkOptical Audio Cable EAfter connecting Digital audio output settingSpeaker/amplifier connection Connect an amplifier with external speakers as shown belowEnquiry Inserting a CA CardModule MenuWhat you can do with Aquos Link Controlling Hdmi devices using Aquos LinkAquos Link connection Aquos Link SetupAquos Link Auto power on Using Genre InfoOperating an Aquos Link device Common operations What is the Menu?Operation without a remote control Menu operationAdvanced Basic adjustmentPicture adjustments Picture SettingsPower Save Settings Audio adjustmentNo Signal Off Audio SettingsNo Operation Off Sleep TimerAuto Installation Programme SetupEErase Programme Analogue channel settingsAnalogue setting SortSubtitle Child LockKey Lock LanguageSelecting the WSS picture size manually Useful Viewing functionsMode Selecting the WSS picture size automaticallyPosition Auto VolumeREC Picture Size Hdmi Auto ViewProgramme Title Display Display SettingsTime Display Game Play TimeOther useful features Selecting the picture size Connecting a PCConnecting a PC Displaying a PC image on the screenFine Sync Input SignalSelecting input resolution Auto SyncRS-232C port specifications RS-232C command list PC compatibility chartPages 29 TroubleshootingAppendix Information on the software license for this productReceiver Report Download SetupReset Message ListOptional accessory SpecificationsOther Countries outside the EU Rating table for Child Lock480.0 Polígono Industrial Can Sant Joan Calle Sena s/n Sharp Corporation