Sharp LC-37B20E, LC-37B20S, LC-37G20E Special Note for Users in the U.K, Blue Neutral Brown Live

Page 2

SPECIAL NOTE FOR USERS IN THE U.K.

The mains lead of this product is fi tted with a non-rewireable (moulded) plug incorporating a 13A fuse. Should the fuse need to be replaced, a BSI or ASTA approved BS 1362 fuse marked or ￿￿￿ and of the same rating as above, which is also indicated on the pin face of the plug, must be used.

Always refi t the fuse cover after replacing the fuse. Never use the plug without the fuse cover fi tted.

In the unlikely event of the socket outlet in your home not being compatible with the plug supplied, cut off the mains plug and fi t an appropriate type.

DANGER:

The fuse from the cut-off plug should be removed and the cut-off plug destroyed immediately and disposed of in a safe manner.

Under no circumstances should the cut-off plug be inserted elsewhere into a 13A socket outlet, as a serious electric shock may occur.

To fi t an appropriate plug to the mains lead, follow the instructions below:

IMPORTANT:

The wires in the mains lead are coloured in accordance with the following code:

Blue: Neutral

Brown: Live

As the colours of the wires in the mains lead of this product may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows:

The wire which is coloured blue must be connected to the plug terminal which is marked N or coloured black.

The wire which is coloured brown must be connected to the plug terminal which is marked L or coloured red. Ensure that neither the brown nor the blue wire is connected to the earth terminal in your three-pin plug. Before replacing the plug cover make sure that:

If the new fi tted plug contains a fuse, its value is the same as that removed from the cut-off plug.

The cord grip is clamped over the sheath of the mains lead, and not simply over the lead wires.

IF YOU HAVE ANY DOUBT, CONSULT A QUALIFIED ELECTRICIAN.

Image 2
Contents Español Nederlands Italiano Français Deutsch English Special Note for Users in the U.K Blue Neutral Brown LiveContents Introduction Important Safety PrecautionsPrecautions when transporting the TV Dear Sharp customerRemote control unit IntroductionTV Front view Remote control sensor OPC sensorOPC indicator Sleep indicator Standby/On indicator TV Rear viewAttaching the stand unit Supplied accessoriesPreparation Preparation Using the remote control unitInserting the batteries Channel search setting Initial installation overviewCountry setting Quick guideSetting the TV on the wall Before turning on the powerSupplying power to the antenna Bundling the cablesConfirm the following before turning on the power Initial auto installationChecking signal strength and channel strength EChecking signal strengthWatching TV Daily operationEPG Overview Useful settings for using EPGEPG Electronic Programme Guide Selecting a programme Check programme information Selecting a programme using EPGBasic Operation EDisplay the EPG screen Search a programme in a categoryESelecting Watch in the timer setup screen Timer recording using EPGCancelling the timer recording ESelecting Record in the timer setup screenUsing the MHEG5 application UK only TeletextIntroduction to connections Connecting external devicesEBefore connecting Hdmi connection C R Component connection Connecting external devicesEAfter connecting Hdmi Audio Select VIDEO/VIDEO connectionControlling devices with Scart using AV Link Scart connectionConnect an amplifier with external speakers as shown below EAfter connecting Digital audio output settingSpeaker/amplifier connection Optical Audio CableMenu Inserting a CA CardModule EnquiryControlling Hdmi devices using Aquos Link What you can do with Aquos LinkUsing Genre Info Aquos Link SetupAquos Link Auto power on Aquos Link connectionOperating an Aquos Link device Menu operation What is the Menu?Operation without a remote control Common operationsPicture Settings Basic adjustmentPicture adjustments AdvancedAudio Settings Audio adjustmentNo Signal Off Power Save SettingsProgramme Setup Sleep TimerAuto Installation No Operation OffSort Analogue channel settingsAnalogue setting EErase ProgrammeLanguage Child LockKey Lock SubtitleSelecting the WSS picture size automatically Useful Viewing functionsMode Selecting the WSS picture size manuallyHdmi Auto View Auto VolumeREC Picture Size PositionGame Play Time Display SettingsTime Display Programme Title DisplayOther useful features Displaying a PC image on the screen Connecting a PCConnecting a PC Selecting the picture sizeAuto Sync Input SignalSelecting input resolution Fine SyncRS-232C port specifications PC compatibility chart RS-232C command listInformation on the software license for this product TroubleshootingAppendix Pages 29Message List Download SetupReset Receiver ReportSpecifications Optional accessoryRating table for Child Lock Other Countries outside the EU480.0 Sharp Corporation Polígono Industrial Can Sant Joan Calle Sena s/n