Sharp LC-32G20E, LC-37B20S Analogue channel settings, Analogue setting, Sort, EErase Programme

Page 29
Press c/d to select “Yes”, and then press OK.
Press c/d to select “Yes”, and then press OK.

Basic adjustment

Analogue channel settings

Setup

Programme Setup

Analogue setting

You can reconfigure Analogue TV channels settings automatically or manually.

EAdditional search

Use this menu to add new channels automatically after auto installation has been made.

Start searching channels after selecting colour system and sound system.

EManual Adjust

Use this menu to set up analogue TV channels manually.

After selecting “Yes” on the screen, press a/b/ c/d to select the channel you want to set and the press OK.

Fine

You can adjust the frequency to the desired position.

NOTE

Adjust while checking the background picture as a reference.

Instead of pressing c/d to adjust the frequency, you can set by directly entering the frequency number of the channel with 0 - 9.

EXAMPLE

179.25 MHz: Press 1 s 7 s 9 s 2 s 5.

49.25 MHz: Press 4 s 9 s 2 s 5 s OK.

Colour sys.

Select the optimum colour system to receive. (Auto, PAL, SECAM)

Sound sys. (Broadcasting systems)

Select the optimum sound systems (Broadcasting systems) to receive. (B/G, D/K, I, L/L’)

Label

When a TV channel sends its Network Name, the Auto Installation detects the information and assigns a name to it. However, you can change individual channel names.

1 Press a/b/c/d to select each character of the new name for the channel, and then press OK.

2 Repeat step 1 above until the name is fully spelt out.

NOTE

The name can be 5 characters or less.

If a channel name is less than 5 characters, select “END” to set the channel name.

Skip

Channels with “Skip” set to “On” are passed over when using PR/PS even if selected while watching the image from the TV.

Decoder

When connecting a decoder to the unit, you need to select EXT1 or EXT2.

NOTE

• “Off” is factory preset value.

Lock

You can block the viewing of any channel.

NOTE

See “Child Lock” for setting a PIN.

When Lock is set to “On” for a channel, “Child lock has been activated.” displays, and the image and sound of the channel are blocked.

When pressing 6 while “Child lock has been activated.” displays, the PIN input menu will display. Inputting the correct PIN lifts the child lock temporarily until the power is turned off.

ESort

Channel positions can be sorted freely.

1

2 Press a/b/c/d to select the channel you want to move, and then press OK.

3 Press a/b/c/d to move it to the desired position, and then press OK.

4 Repeat steps 3 and 4 until all desired channels are sorted.

EErase Programme

An individual programme can be erased.

1

2 Press a/b/c/d to select the channel you want to erase, and then press OK.

• A message screen pops up.

3 Press c/d to select “Yes”, and then press OK to erase the selected programme. All the subsequent programmes move up.

4 Repeat steps 3 and 4 until all desired channels are erased.

27

Image 29
Contents Español Nederlands Italiano Français Deutsch English Blue Neutral Brown Live Special Note for Users in the U.KContents Precautions when transporting the TV Important Safety PrecautionsIntroduction Dear Sharp customerIntroduction Remote control unitOPC indicator Sleep indicator Standby/On indicator Remote control sensor OPC sensorTV Front view TV Rear viewAttaching the stand unit Supplied accessoriesPreparation Preparation Using the remote control unitInserting the batteries Country setting Initial installation overviewChannel search setting Quick guideSupplying power to the antenna Before turning on the powerSetting the TV on the wall Bundling the cablesChecking signal strength and channel strength Initial auto installationConfirm the following before turning on the power EChecking signal strengthDaily operation Watching TVEPG Overview Useful settings for using EPGEPG Electronic Programme Guide Basic Operation EDisplay the EPG screen Selecting a programme using EPGSelecting a programme Check programme information Search a programme in a categoryCancelling the timer recording Timer recording using EPGESelecting Watch in the timer setup screen ESelecting Record in the timer setup screenTeletext Using the MHEG5 application UK onlyIntroduction to connections Connecting external devicesEBefore connecting EAfter connecting Hdmi Audio Select Connecting external devicesHdmi connection C R Component connection VIDEO/VIDEO connectionScart connection Controlling devices with Scart using AV LinkSpeaker/amplifier connection EAfter connecting Digital audio output settingConnect an amplifier with external speakers as shown below Optical Audio CableModule Inserting a CA CardMenu EnquiryWhat you can do with Aquos Link Controlling Hdmi devices using Aquos LinkAquos Link Auto power on Aquos Link SetupUsing Genre Info Aquos Link connectionOperating an Aquos Link device Operation without a remote control What is the Menu?Menu operation Common operationsPicture adjustments Basic adjustmentPicture Settings AdvancedNo Signal Off Audio adjustmentAudio Settings Power Save SettingsAuto Installation Sleep TimerProgramme Setup No Operation OffAnalogue setting Analogue channel settingsSort EErase ProgrammeKey Lock Child LockLanguage SubtitleMode Useful Viewing functionsSelecting the WSS picture size automatically Selecting the WSS picture size manuallyREC Picture Size Auto VolumeHdmi Auto View PositionTime Display Display SettingsGame Play Time Programme Title DisplayOther useful features Connecting a PC Connecting a PCDisplaying a PC image on the screen Selecting the picture sizeSelecting input resolution Input SignalAuto Sync Fine SyncRS-232C port specifications RS-232C command list PC compatibility chartAppendix TroubleshootingInformation on the software license for this product Pages 29Reset Download SetupMessage List Receiver ReportOptional accessory SpecificationsOther Countries outside the EU Rating table for Child Lock480.0 Polígono Industrial Can Sant Joan Calle Sena s/n Sharp Corporation