Sharp LC-32G20S, LC-37B20S, LC-37G20E, LC-37B20E, LC-37G20S, LC-32G20E Watching TV, Daily operation

Page 12

Watching TV

Daily operation

Switching on/off

Turning on/off the power

Press A on the TV.

Switch it off by pressing A on the TV.

• However, please bear in mind that EPG data (electronic programme guide) will be lost, and programmed timer recordings will not be performed by the TV.

Standby mode

ETo standby mode

If the TV set is switched on, you can switch it to standby by pressing B on the remote control.

ESwitching on from standby

From standby, press B on the remote control.

TV indicator status

B indicator

Status

Off

Power off

Green

Power on

Red

Standby

NOTE

If you are not going to use this TV for a long period of time, be sure to remove the AC cord from the power outlet.

A small amount of electric power is still consumed even when A is turned off.

Switching between analogue and digital broadcasts

EWatching digital

EWatching analogue

broadcasts

broadcasts

Changing channels

With PR/PS: With 0 - 9:

10

Selecting external video source

Once the connection is made, press

 

 

 

INPUT SOURCE

B to display the INPUT SOURCE

TV

screen, and then press a/b to switch

EXT1

over to the appropriate external source

EXT2

with OK.

EXT3

 

 

 

EXT4

 

 

 

EXT5

 

 

 

 

Selecting Sound mode

DTV mode:

EIf multi sound modes are received, each time you press 2 the mode switches as follows.

Audio (ENG) : STEREO

L/R L R LR

Audio (ENG) : CH A

CH A CH B CH AB

Audio (ENG) : MONO

EPress c/d to select L or R sound when the STEREO or DUAL MONO screen is displayed.

Audio (ENG) : STEREO

L/R L R LR

NOTE

The sound mode OSD disappears in 6 seconds.

Selectable items vary depending on the received broadcasts.

ATV mode:

Each time you press 2, the mode switches as illustrated in the following tables.

 

NICAM TV broadcasts selection

Signal

 

Selectable items

Stereo

 

NICAM STEREO, MONO

Bilingual

 

NICAM CH A, NICAM CH B, NICAM CH AB,

 

MONO

 

 

Monaural

 

NICAM MONO, MONO

 

 

A2 TV broadcasts selection

Signal

 

Selectable items

Stereo

 

STEREO, MONO

Bilingual

 

CH A, CH B, CH AB

Monaural

 

MONO

NOTE

When no signal is input, the sound mode will display “MONO”.

Image 12
Contents Español Nederlands Italiano Français Deutsch English Special Note for Users in the U.K Blue Neutral Brown LiveContents Important Safety Precautions Precautions when transporting the TVIntroduction Dear Sharp customerRemote control unit IntroductionRemote control sensor OPC sensor OPC indicator Sleep indicator Standby/On indicatorTV Front view TV Rear viewSupplied accessories PreparationAttaching the stand unit Using the remote control unit Inserting the batteriesPreparation Initial installation overview Country settingChannel search setting Quick guideBefore turning on the power Supplying power to the antennaSetting the TV on the wall Bundling the cablesInitial auto installation Checking signal strength and channel strengthConfirm the following before turning on the power EChecking signal strengthWatching TV Daily operationUseful settings for using EPG EPG Electronic Programme GuideEPG Overview Selecting a programme using EPG Basic Operation EDisplay the EPG screenSelecting a programme Check programme information Search a programme in a categoryTimer recording using EPG Cancelling the timer recordingESelecting Watch in the timer setup screen ESelecting Record in the timer setup screenUsing the MHEG5 application UK only TeletextConnecting external devices EBefore connectingIntroduction to connections Connecting external devices EAfter connecting Hdmi Audio SelectHdmi connection C R Component connection VIDEO/VIDEO connectionControlling devices with Scart using AV Link Scart connectionEAfter connecting Digital audio output setting Speaker/amplifier connectionConnect an amplifier with external speakers as shown below Optical Audio CableInserting a CA Card ModuleMenu EnquiryControlling Hdmi devices using Aquos Link What you can do with Aquos LinkAquos Link Setup Aquos Link Auto power onUsing Genre Info Aquos Link connectionOperating an Aquos Link device What is the Menu? Operation without a remote controlMenu operation Common operationsBasic adjustment Picture adjustmentsPicture Settings AdvancedAudio adjustment No Signal OffAudio Settings Power Save SettingsSleep Timer Auto InstallationProgramme Setup No Operation OffAnalogue channel settings Analogue settingSort EErase ProgrammeChild Lock Key LockLanguage SubtitleUseful Viewing functions ModeSelecting the WSS picture size automatically Selecting the WSS picture size manuallyAuto Volume REC Picture SizeHdmi Auto View PositionDisplay Settings Time DisplayGame Play Time Programme Title DisplayOther useful features Connecting a PC Connecting a PCDisplaying a PC image on the screen Selecting the picture sizeInput Signal Selecting input resolutionAuto Sync Fine SyncRS-232C port specifications PC compatibility chart RS-232C command listTroubleshooting AppendixInformation on the software license for this product Pages 29Download Setup ResetMessage List Receiver ReportSpecifications Optional accessoryRating table for Child Lock Other Countries outside the EU480.0 Sharp Corporation Polígono Industrial Can Sant Joan Calle Sena s/n