Sharp LC-60LE832U, LC-40LE832U, LC-46LE832U, LC-52LE832U Troubleshooting, Pages 24, Pages 27

Appendix

Troubleshooting

Problem	Possible Solution
• No power	• Check if you pressed POWER on the remote control unit. Page 18

•Is the AC cord disconnected? Page 9

•Has the power been turned on? Page 18

• Unit cannot be operated.	• External infl uences such as lightning, static electricity, may cause improper
	operation. In this case, operate the unit after fi rst turning off the power of the TV or
	unplugging the AC cord and replugging it in after 1 or 2 minutes.
• Remote control unit does not	• Is the equipment to be operated by the remote control unit set correctly? Press TV
operate.	to set the remote control unit to the setting for operating the TV.
	• Are batteries inserted with polarity (e, f) aligned? Page 10
	• Are batteries worn out? (Replace with new batteries.)
	• Are you using it under strong or fl uorescent lighting?
	• Is a fl uorescent light illuminated near the remote control sensor?
	• Is "RC Control Lock" selected in "Operation Lock Out"? Page 33
• Picture is cut off/with sidebar	• Is the image position correct? Pages 32 and 57
screen.	• Are screen mode adjustments such as picture size made correctly?
	Pages 24 and 56
• Strange color, light color, or color	• Adjust the picture tone.	Pages 27 and 28
misalignment	• Is the room too bright? The picture may look dark in a room that is too bright.
• Power is suddenly turned off.	• Is the sleep timer set?	Page 21
	• Check the power control settings. Page 30
	• The unit's internal temperature has increased. Remove any objects blocking vent or
	clean.

• No sound • Is connection to other components correct? Pages 13 to 17 and 52

•Is the volume too low? Page 21

•Is "Variable" selected in "Output Select"? Page 32

•Have you pressed MUTE on the remote control unit? Page 21

•Check the audio output of the connected external equipment. Is the volume too low or muted?

•When external equipment is connected via an HDMI cable, you may need to confi gure the audio to be output through the HDMI cable.

•When audio is not output from external equipment connected to the PC IN or HDMI 1 terminal, check the "Audio Select" setting. Page 57

•Even when external equipment is connected using an HDMI-certifi ed cable, an audio cable connection may be required depending on the type of equipment and the media being played back. In this case, in addition to connecting an HDMI-certifi ed cable to the HDMI 1 terminal, connect a Ø 3.5 mm stereo minijack cable to the AUDIO IN terminal and set "Audio Select" to "HDMI+Analog". Page 57

•When connecting a PC via an HDMI-certifi ed cable, check the following:

-Is the audio output of the PC confi gured correctly? Check the audio output settings and output audio format in Sound Properties on the PC.

Only PCM format audio can be output. Compressed audio (with a sampling rate of 32kHz, 44.1kHz, or 48kHz) and DTS format audio cannot be output.

-Depending on the board, only video signals may be output. In this case, in addition to connecting an HDMI-certifi ed cable to the HDMI 1 terminal, connect a Ø 3.5 mm stereo minijack cable to the AUDIO IN terminal and set "Audio Select" to "HDMI+Analog". Page 57

•If you are using a DVI-HDMI conversion cable to connect external equipment to the TV, check the following:

-Is an audio cable connected? The DVI-HDMI conversion cable is for video only. Connect a Ø 3.5 mm stereo minijack cable to listen to the audio.

-Is HDMI 1 being used? When the TV is connected to another HDMI terminal, the audio and video are not output together even if a Ø 3.5 mm stereo minijack cable is connected to the shared AUDIO IN terminal for PC IN and HDMI 1.

-Check the "Audio Select" setting. Set "Audio Select" to "HDMI+Analog". Page 57

73