Sharp LC-52LE925UN operation manual PC Control of the TV

Page 62

Using a PC

PC Control of the TV

The TV can be controlled from a PC using the RS- 232C or IP.

Use a cross-type RS-232C cable, ETHERNET cable (commercially available) or wireless LAN USB adapter for the connections.

This operation system should be used by a person who is accustomed to using computers.

Communication conditions for IP

Connect to the TV with the following settings made for IP on the PC.

IP protocol:

TCP/IP

Host IP address:

Set the IP address on the TV menu

Service:

None (Do not select Telnet or SSH)

TCP port#:

Set a port number on the TV menu

 

(Control port)

When you set your ID and password on the TV menu, you need to enter them as soon as you connect to the TV.

The connection will be cut off when there has been no communication for 3 minutes.

Communication conditions for RS-232C

Set the RS-232C communication settings on the PC to match the TV's communication conditions.

The TV's communication settings are as follows:

Baud rate:

9,600 bps

Data length:

8 bits

Parity bit:

None

Stop bit:

1 bit

Flow control:

None

Communication procedure

Send the control commands from the PC via the RS- 232C or IP.

The TV operates according to the received command and sends a response message to the PC.

Do not send multiple commands at the same time. Wait until the PC receives the OK response before sending the next command.

Command format

Eight ASCII codes e CR

C1 C2 C3 C4 P1 P2 P3 P4

Command 4-digits Parameter 4-digits Return code

IP Control Setup

Example

Initial Menu

Setup

Initial Setup

EZ Setup

Broadcasting Setup

Internet Setup

Language

[English]

DivX® Setup

Command 4-digits: Command. The text of four characters.

Parameter 4-digits: Parameter 0–9, x, blank, ?

Parameter

Input the parameter values, aligning left, and fi ll with blank(s) for the remainder. (Be sure that 4 values are input for the parameter.)

When the input parameter is not within an adjustable range, “ERR” returns. (Refer to “Response code format”.) Any numerical value can replace the “x” on the table.

0

 

 

 

When “?” is input for some

 

 

 

 

commands, the

 

 

 

 

 

 

 

 

 

 

 

 

0

0

0

9

present setting

?

 

 

 

 

 

 

 

value responds.

 

 

 

 

 

 

 

 

 

 

 

 

a

3

0

 

 

?

?

?

?

 

 

 

 

 

 

 

 

 

1Press MENU to display the MENU screen, and then press c/d to select "Initial Setup".

2Press a/b to select "Internet Setup", and then press ENTER.

3Press a/b to select "Network Setup", and then press ENTER.

4Press a/b to select "IP Control Setup", and then press ENTER.

5Press c/d to select "Change", and then press

ENTER.

6To use IP Control, select "Enable".

7Set the device name.

8Set your login ID and password.

9Set the port to use with IP Control.

10Confi rm the settings, and then press "OK".

Response code format

Normal response

Problem response (communication

 

 

 

 

error or incorrect command)

O K

 

 

 

 

 

 

 

 

 

 

 

E R R

 

 

 

Return code (0DH)

Return code (0DH)

 

 

 

 

 

 

 

 

60

Image 62
Contents LC-52LE925UN LC-60LE925UN Page Model No To aid reporting in case of loss or theft, please recordFCC Compliance Statement Industry Canada StatementAdditional Safety Information Dear Sharp CustomerPrecautions when transporting the TV Caring for the cabinetChild Safety Caring for the front panel3D Glasses Contents Insert the stand into the openings on the rear Supplied AccessoriesAttaching the Stand Connection guide g1Remote control sensor Using the Remote Control UnitInsert the batteries into the remote control unit. See Bundle the cords properly with the cable clampPreparation Installing Batteries in the Remote Control UnitConnecting Antenna Cable AntennasTV Rear Part NamesTV Front Remote Control Unit Part NamesTypes of Connection Introduction to ConnectionsExperiencing HD Images Displaying an External Equipment ImageWhen using DVI-HDMI conversion cable Hdmi Connecting to External EquipmentWhen using Hdmi cable Hdmi 1, 2, 3 or Back panel vertical inputsWhen using Composite cable Video Connecting to External EquipmentWhen using Component cable Component Back panel horizontal inputsConnecting an Audio Amplifier Connecting an AV AmplifierConnecting a PC When using analog RGB cable PC Back panel vertical inputsWatching TV Turning On/Off the Power Initial InstallationLanguage Language setting TV LocationWatching TV Antenna & Cable/STB Air/Cable Antenna settingExamples of the settings confirmation screen CompletedDirect Button Operation Changing VolumeSleep Timer Changing ChannelsExample When the input source is PC in or Hdmi 1 to Press Power SavingExample When the input source is TV, Component or Direct Button OperationExamples Closed Captions and Digital Closed CaptionsPress CC This will present the Closed Caption information displayFor HD programs Press View ModeYou can select the screen size For 43 programsOn-Screen Display Menu Operation Using the remote controlOn-Screen Display Menu Menu Operation ButtonsMenu Items On-Screen Display MenuOPC Setting Picture SettingsAV Mode Changing Pic.Quality Advanced Picture SettingsFilm Mode 32 pull-down Color Temp Color TemperatureGamma Adjustment Motion Enhancement3D Surround Audio SettingsAuto Volume Bass EnhancerNo Signal Off Power ControlPower Saving Audio OnlySystem Options View OptionInput Terminal Setting Menu DesignCaption Setup Icon Light Up SettingDemo Mode Game Play TimeBroadcasting Setup Initial SetupEZ Setup CH SetupReset Individual SetupWall Mount Audio Setup LanguageChip is an electronic fi ltering device built into your When setting an individual content-based rating itemChip TV Parental GuidelinesCanadian French Ratings How to temporarily release the V-CHIP BlockCanadian English Ratings Reactivating the temporarily released V-CHIP BlockIdentification Software UpdateInformation Digital Caption Info Digital Caption InformationUpdating the Software via the Network Call 1-800-BE-SHARPAfter the screen shown below is displayed, press Press Enter to start updatingDuring the data checking, Checking blinks Remove the USB memory deviceEnjoying 3D Image Viewing Display Methods for 3D and 2D ImagesEnjoying 3D Image Viewing Supplied Accessories for 3D Glasses3D Glasses Part NamesAttaching the 3D Glasses Band Attaching the Nose Pad Before Using the 3D GlassesReplacing the Battery Usage Range of the 3D Glasses Using the 3D GlassesViewing 3D Images Watching 2D Images in 3D Switching to the Previous ModeSwitching from 3D to 2D Mode 3D Menu3D Brightness Boost Configuring the TV Settings to Enhance 3D Image Viewing3D Setup 3D Glasses infrared receiver Specifications 3D Glasses3D Glasses lenses Enjoying Photo/Music/Video Playback When displaying the data with the Input list screenWhen displaying the data with the Apps Viewing Photos, Listening to Music and Watching VideosViewing Individual Photos Photo ModeViewing Thumbnails Slide ShowSelect Slide Show BGM Set/Reset All Slide Show ImageSelect Slide Show Interval Buttons for slide show BGM select operationMusic Mode Video ModeUSB Memory Device Compatibility DivX SetupUsing the control panel DivX VOD registration DivX VOD deregistrationOther Viewing Options Presetting Remote Control FunctionPresetting manufacturer codes Operating the Connected EquipmentOther Viewing Options Manufacturer codes Using Aquos Link Controlling Hdmi Equipment Using Aquos LinkOne Touch Playback Using Aquos LinkAquos Link Setup Start/Stop Recording Link Operation MenuOne Touch Recording Turning On/Off Aquos LINK-compatible EquipmentPlayback of Titles Using Aquos Link Using the Device Operation PanelTimer Recording Manually Changing Aquos Audio Speaker System’s Sound ModeStretch Dot by Dot Using a PCDisplaying a PC Image on the Screen PC Compatibility Chart Adjusting the PC ImageSetting Audio Input Using a PCPC Control of the TV Using a PC Command table Commands not indicated here are not guaranteed to operateUsing an Ethernet cable Using the InternetConnecting to the Internet About the original homeUsing the Internet Using the wireless LAN USB adapterWireless Setup Internet SetupInteractive Service Checking Your Internet ConnectionSetting the Zip Code Displaying Updated Information and Support ServiceSetting the Country Sidebar WidgetEntering Text Software Keyboard About links Using the BrowserFeatured Content Selected item Description Select This Using the Toolbar Using TabsSelected item Close This TabEditing Bookmarks Saving the URL of the CurrentOpening a Bookmarked View Settings Browser SettingsSecurity Settings HIf you do not have a Netflix account Settings for Watching Netflix Content on the TVInstantly Watching Movies from Netflix If you have a Netflix accountHThe buttons that can be used during playback Adding Content to the Instant QueueDeactivating Netflix Function Getting Started Vudu Movies featuresEnjoying Movies and Internet Applications with Vudu Watching a Movie on VuduOperational buttons during playback Troubleshooting VuduDeactivating the Vudu Function Disclaimers Before detaching or attaching the stand, unplug the AC cord AppendixRemoving the Stand LC-52LE925UN Before attaching/detaching the standUsing an optional bracket to mount the TV Setting the TV on the WallOptional Accessories AppendixPages 26 TroubleshootingPages 23 Troubleshooting 3D Images Troubleshooting Error MessageCH Setup Broadcasting Setup Initial Setup menuSoftware Update Information menu TrademarksSpecifications Model LC-52LE925UN Model LC-60LE925UNSpecification Wireless LAN USB AdapterSpecifications Information on the Software License for This Product Calling for Service Limited WarrantyPage Page 55/64 AN-52AG4 Dimensional Drawings15/64 AN-52AG4 Sharp Electronics Corporation