Sharp LC-32E67U Preparation, Antennas, Installing Batteries in the Remote Control Unit

Page 10

Preparation

Antennas

To enjoy a clearer picture, use an outdoor antenna. The following is a brief explanation of the types of connections that are used for a coaxial cable. If your outdoor antenna uses a 75-ohm coaxial cable with an F-type connector, plug it into the antenna terminal at the rear of the TV set.

1.A 75-ohm system is generally a round cable with F-type connector that can easily be attached to a terminal without tools (Commercially available).

2.A 300-ohm system is a fl at “twin-lead” cable that can be attached to a 75-ohm terminal through a 300/75-ohm adapter (Commercially available).

F-type connector

75-ohm coaxial cable (round)

300-ohm twin-lead cable (fl at)

NOTICE F-type connector should be finger-tightened only.

When connecting the RF cable to the TV set, do not tighten F-type connector with tools.

If tools are used, it may cause damage to your TV set. (The breaking of internal circuit, etc.)

F-type connector

75-ohm coaxial cable

Connecting Antenna Cable

• Connect the antenna cable to the TV using one of the methods in the illustration as shown (1, 2, 3 or 4).

1Cable without a CATV converter

2VHF/UHF antenna

3Combination VHF/ UHF antenna

4Separate VHF/UHF antenna

 

Home Antenna

Cable TV lead-In

terminal (75-ohm)

 

 

Coaxial cable

 

(commercially available)

 

Home Antenna

75-ohm coaxial cable (round)

terminal (75-ohm)

 

 

Coaxial cable

 

(commercially available)

75-ohm coaxial cable (round)

 

 

or

 

300/75-ohm adapter

300-ohm twin-lead cable (flat)

(commercially available)

 

VHF

UHF

300-ohm

 

 

ANTENNA

ANTENNA

 

 

twin-lead cable

 

 

 

 

 

 

 

 

 

IN

OUT

 

300-ohm twin-lead cable

Combiner

 

 

 

 

 

or

 

 

(commercially available)

75-ohm coaxial cable

 

 

 

 

 

To TV antenna terminal

Installing Batteries in the Remote Control Unit

If the remote control fails to operate TV functions, replace the batteries in the remote control unit.

1Open the battery cover.

2Insert two “AAA” size batteries (supplied with the product).

3Close the battery cover.

•Place the batteries with their terminals corresponding to the (e) and (f) indications in the battery compartment.

CAUTION

Improper use of batteries can result in chemical leakage or explosion. Be sure to follow the instructions below.

•Do not mix batteries of different types. Different types of batteries have different characteristics.

•Do not mix old and new batteries. Mixing old and new batteries can shorten the life of new batteries or cause chemical leakage in old batteries.

•Remove batteries as soon as they are worn out. Chemicals that leak from batteries that come in contact with skin can cause a rash. If you fi nd any chemical leakage, wipe thoroughly with a cloth.

•The batteries supplied with this product may have a shorter life expectancy due to storage conditions.

•If you will not be using the remote control unit for an extended period of time, remove batteries from it.

8

Page 9 Page 11
Image 10
Page 9 Page 11
Contents
LC-32E67U Page LC-32E67U Trademarks Declaration of ConformityAdditional Safety Information Dear Sharp CustomerPrecautions when transporting the TV Tune Into Safety IssueThis Manufacturer Cares Supplied Accessories Attaching the StandUsing the Remote Control Unit Power indicator on the front of the television lights GreenClose the battery cover Installing Batteries in the Remote Control UnitConnecting Antenna Cable PreparationContents TV Rear/Side Part NamesTV Front Input buttonRemote Control Unit When using the remote control unit, point it at the TVWhen using composite cable Input Connecting to External EquipmentConnecting Audiovisual Equipment When using component cable Input 1 orConnecting a PC Using Digital Audio OutputConnecting Hdmi Equipment When connecting to a PC with an analog RGB terminal InputInitial Setup Turning On/Off the PowerWatching TV Direct Button Operation Changing VolumeSleep Timer Changing ChannelsMTS/SAP stereo mode Digital broadcasting audio modePress Power Saving Closed Captions and Digital Closed CaptionsYou can select the screen size Press View ModeFor PC input mode For 43 programsOn-Screen Display Menu For TV/INPUT 1/2/3 ModeFor HDMI/PC-IN Mode Menu ItemsOn-Screen Display Menu Operation Using the remote controlUsing the control panel of the main unit Menu Operation ButtonsAdvanced Picture Setting OPC SettingPicture Menu Surround Audio MenuBass Enhancer Power Control Menu Setup MenuInput Skip CH SetupPC Setup Input LabelPosition Audio SetupReset PC Audio SelectParental Ctrl Parental Control Setting Mpaa Voluntary movie rating system RatingCanadian French Ratings How to temporarily release the V-CHIP BlockCanadian English Ratings Reactivating the temporarily released V-CHIP BlockOption Menu Demo Mode Favorite CH Favorite Channel SettingSoftware Update Operation Lock OutAfter the screen shown below is displayed, press During the data checking, Checking blinksPress Enter to start updating EnterPresetting Remote Control Function Other Viewing OptionsOther Viewing Options Manufacturer codes Using Aquos Link Controlling Hdmi Equipment Using Aquos LinkOne Touch Recording Aquos Link SetupAuto Power On Selecting RecorderOne Touch Playback Timer RecordingAquos Link Menu Press d to start playing back a titleSelecting Media Type for Aquos Link Compatible Recorder Playback of Titles Using Aquos LinkManually Changing Aquos Audio Speaker System’s Sound Mode Hdmi Device SelectionAppendix Setting the TV on the WallRemoving the Stand Error message about reception of broadcast TroubleshootingTroubleshooting-Digital Broadcasting Problem Possible SolutionRS-232C Port Specifications Model LC-32E67U Optional AccessorySpecifications Part name Model numberInformation on the Software License for This Product PC Compatibility ChartClearing the Secret Number Calling for Service Limited WarrantyDimensional Drawings Sharp Electronics Corporation