Sharp LC-32E67U operation manual CH Setup, PC Setup, Input Skip, Input Label

Page 26

On-Screen Display Menu

CH Setup

If initial setup does not memorize all the channels in your region, follow the instructions below to manually memorize the channels.

Air/Cable: Make sure what kind of connection is made with your TV when selecting "Air" or "Cable".

CH Search: Channel auto search makes the TV look for all channels viewable in the set area.

CH Memory: You can select the channels to skip in each ANALOG (Air), ANALOG (Cable), DIGITAL (Air) and DIGITAL (Cable).

On: Skips channels. (Channel selection disabled using CH r/s.)

Off: Does not skip channels. (Channel selection enabled using CHr/s.)

PC Setup

Input Signal (for Analog PC Input Mode Only)

Some input signals may have to be registered manually to display properly. The pair of input signals (resolutions) in the list below is not distinguishable when received.

In such a case, you have to set the correct signal manually. After setting once, it will display when the same signal (resolution) is input again.

1024 x 768

1360 x 768

You can only select the "Input Signal" on the Setup menu when receiving one of the 2 input signals listed above.

Antenna Setup Digital: In order to receive digital air broadcasts, you need a digital broadcast antenna. You can confi rm the antenna confi guration through the "Antenna Setup Digital" screen. If necessary, adjust the direction of the antenna to obtain the maximum signal strength.

Signal Strength: The signal strength of DIGITAL channel is displayed. The signal information is based on the current channel.

Channel Strength: Input the 2-digit channel number to check the signal strength of the selected channel. Make sure the signal is strong enough for each channel.

• This function is available for DIGITAL (Air) only.

Auto Sync. (for Analog PC Input Mode Only)

For automatically adjusting the PC image.

Yes: Auto Sync. starts.

No: This function does not work.

When Auto Sync. is successful, "Completed" displays. If not, Auto Sync. failed.

Auto Sync. may fail even if "Completed" displays.

Auto Sync. may fail if the computer image has low resolution, has unclear (black) edges, or is moved while executing Auto Sync.

Be sure to connect the PC to the TV and switch it on before starting Auto Sync.

See "Initial Setup" on page 14 for setting each item.

If no channel is found, confi rm the type of connection made with your TV and try channel search again.

Input Skip

This setting allows you to skip the HDMI or PC-IN Input ("Input 4 (PC)", "Input 5 (HDMI)", "Input 6 (HDMI)", "Input 7 (HDMI)" and "Input 8 (HDMI)") on the Input Selection operation.

Yes: Skips the input.

No: Does not skip input.

Input Label

Lets you set the input terminal displayed when using the INPUT SOURCE menu or channel display. Press a/b/c/d to select the new name for the input mode.

• You cannot change labels if the INPUT SOURCE is TV.

Fine Sync.

Ordinarily you can easily adjust the picture as necessary to change image position using Auto Sync. In some cases, however, manual adjustment is needed to optimize the image.

H-Pos.:Centers the image by moving it to the left or right.

V-Pos.:Centers the image by moving it up or down.

Clock: Adjust when the image fl ickers with vertical stripes.

Phase: Adjust when characters have low contrast or when the image fl ickers.

For resetting all Fine Sync. adjustment items to the factory preset values, press a/b to select "Reset", and then press

ENTER.

It is not necessary to adjust the "Clock" or "Phase" when a digital signal is being input, so it cannot be selected.

The default cursor position may not be in the center, because the screen position variable ranges may be asymmetrical.

24

Image 26
Contents LC-32E67U Page LC-32E67U Trademarks Declaration of ConformityAdditional Safety Information Dear Sharp CustomerPrecautions when transporting the TV This Manufacturer Cares IssueTune Into Safety Supplied Accessories Attaching the StandUsing the Remote Control Unit Power indicator on the front of the television lights GreenClose the battery cover Installing Batteries in the Remote Control UnitConnecting Antenna Cable PreparationContents TV Rear/Side Part NamesTV Front Input buttonRemote Control Unit When using the remote control unit, point it at the TVWhen using composite cable Input Connecting to External EquipmentConnecting Audiovisual Equipment When using component cable Input 1 orConnecting a PC Using Digital Audio OutputConnecting Hdmi Equipment When connecting to a PC with an analog RGB terminal InputWatching TV Turning On/Off the PowerInitial Setup Direct Button Operation Changing VolumeSleep Timer Changing ChannelsMTS/SAP stereo mode Digital broadcasting audio modePress Power Saving Closed Captions and Digital Closed CaptionsYou can select the screen size Press View ModeFor PC input mode For 43 programsOn-Screen Display Menu For TV/INPUT 1/2/3 ModeFor HDMI/PC-IN Mode Menu ItemsOn-Screen Display Menu Operation Using the remote controlUsing the control panel of the main unit Menu Operation ButtonsPicture Menu OPC SettingAdvanced Picture Setting Bass Enhancer Audio MenuSurround Power Control Menu Setup MenuInput Skip CH SetupPC Setup Input LabelPosition Audio SetupReset PC Audio SelectParental Ctrl Parental Control Setting Mpaa Voluntary movie rating system RatingCanadian French Ratings How to temporarily release the V-CHIP BlockCanadian English Ratings Reactivating the temporarily released V-CHIP BlockOption Menu Demo Mode Favorite CH Favorite Channel SettingSoftware Update Operation Lock OutAfter the screen shown below is displayed, press During the data checking, Checking blinksPress Enter to start updating EnterPresetting Remote Control Function Other Viewing OptionsOther Viewing Options Manufacturer codes Using Aquos Link Controlling Hdmi Equipment Using Aquos LinkOne Touch Recording Aquos Link SetupAuto Power On Selecting RecorderOne Touch Playback Timer RecordingAquos Link Menu Press d to start playing back a titleSelecting Media Type for Aquos Link Compatible Recorder Playback of Titles Using Aquos LinkManually Changing Aquos Audio Speaker System’s Sound Mode Hdmi Device SelectionRemoving the Stand Setting the TV on the WallAppendix Error message about reception of broadcast TroubleshootingTroubleshooting-Digital Broadcasting Problem Possible SolutionRS-232C Port Specifications Model LC-32E67U Optional AccessorySpecifications Part name Model numberClearing the Secret Number PC Compatibility ChartInformation on the Software License for This Product Calling for Service Limited WarrantyDimensional Drawings Sharp Electronics Corporation