Other Viewing Options

Sharp LC-32E67U operation manual Other Viewing Options, Presetting Remote Control Function

Page 34

Presetting Remote Control Function

Operating the Connected Equipment

You can operate the connected AV products (AV receiver, cable box, SAT tuner, DTV, VCR, DVD, LD) using the presetting manufacturer function of your remote control unit.

	1	6
	2	7
	3	8
	4	9
	4	10
		10
	5
		11
		12
		13
		14

Presetting manufacturer codes

1Press FUNCTION until the LED for your device lights up.

2After the LED for your device lights up, press FUNCTION and DISPLAY at the same time to enter the code registration mode. The LED will blink.

3Press 0–9to enter the manufacturer code. (See page 33.)

•Preset mode is ﬁ nished once the LED no longer lights up.

4After registering the code, the LED will stop blinking then turn off after one second. (If you perform an incorrect operation, the LED will blink quickly then turn off.)

To operate the connected equipment, press FUNCTION to select the LED for your device. (VCR, AUDIO, CBL/SAT (cable converter) or DVD.) The LED lights up, and the remote control unit button will function as follows.

•When you operate VCR or DVD, press INPUT to select the terminal connected to your device.

•CABLE and SAT cannot be selected at the same time.

1 SOURCE POWER

• Turns the connected equipment power on and off.

•Rewinds the tape and allows picture search. (VCR)

•Hold down to go in reverse. (DVD)

3REC

•Starts recording. (VCR)

•Pressing quickly once takes you to the start of the chapter currently playing. Each time you press it, you move back to the start of the previous chapter. (DVD)

50–9(CBL/SAT), • (DOT) (SAT)

•Press a button (or buttons) that corresponds to the channel that you wish to watch.

•Starts playback. (VCR, DVD)

•Rapidly advances the tape and allows picture search. (VCR)

•Hold down to fast forward. (DVD)

•Sets pauses and still pictures. (VCR, DVD)

•Stops the tape transport. (VCR)

•Playback stops when pressed. With some DVD players, pressing the button twice may open the disc tray. (DVD)

10L

•Pressing quickly once takes you to the start of the next chapter. Each time you press it, you move ahead to the start of the next chapter. (DVD)

11FLASHBACK

•Press to switch between the current channel and the channel you were watching immediately before. Some manufacturers do not preset FLASHBACK. (CBL)

12CHr/s

•Press CHror CHsto tune in to a higher or lower channel. (CBL)

•Press to select the channel of the TV tuner on the VCR. (VCR)

13MENU

•When this button is pressed, the DVD menu will display.

14a/b/c/d, ENTER

•a/b/c/d: Press the button to select items on the SAT GUIDE screen or SAT MENU screen. (SAT). Press the button to select items on the DVD MENU screen. (DVD)

•ENTER: Press to activate the selected function. (SAT, DVD)

Image 34

Contents

LC-32E67U Page LC-32E67U Trademarks Declaration of ConformityAdditional Safety Information Dear Sharp CustomerPrecautions when transporting the TV Tune Into Safety IssueThis Manufacturer Cares Supplied Accessories Attaching the StandUsing the Remote Control Unit Power indicator on the front of the television lights GreenClose the battery cover Installing Batteries in the Remote Control UnitConnecting Antenna Cable PreparationContents TV Rear/Side Part NamesTV Front Input buttonRemote Control Unit When using the remote control unit, point it at the TVWhen using composite cable Input Connecting to External EquipmentConnecting Audiovisual Equipment When using component cable Input 1 orConnecting a PC Using Digital Audio OutputConnecting Hdmi Equipment When connecting to a PC with an analog RGB terminal InputInitial Setup Turning On/Off the PowerWatching TV Direct Button Operation Changing VolumeSleep Timer Changing ChannelsMTS/SAP stereo mode Digital broadcasting audio modePress Power Saving Closed Captions and Digital Closed CaptionsYou can select the screen size Press View ModeFor PC input mode For 43 programsOn-Screen Display Menu For TV/INPUT 1/2/3 ModeFor HDMI/PC-IN Mode Menu ItemsOn-Screen Display Menu Operation Using the remote controlUsing the control panel of the main unit Menu Operation ButtonsAdvanced Picture Setting OPC SettingPicture Menu Surround Audio MenuBass Enhancer Power Control Menu Setup MenuInput Skip CH SetupPC Setup Input LabelPosition Audio SetupReset PC Audio SelectParental Ctrl Parental Control Setting Mpaa Voluntary movie rating system RatingCanadian French Ratings How to temporarily release the V-CHIP BlockCanadian English Ratings Reactivating the temporarily released V-CHIP BlockOption Menu Demo Mode Favorite CH Favorite Channel SettingSoftware Update Operation Lock OutAfter the screen shown below is displayed, press During the data checking, Checking blinksPress Enter to start updating EnterPresetting Remote Control Function Other Viewing OptionsOther Viewing Options Manufacturer codes Using Aquos Link Controlling Hdmi Equipment Using Aquos LinkOne Touch Recording Aquos Link SetupAuto Power On Selecting RecorderOne Touch Playback Timer RecordingAquos Link Menu Press d to start playing back a titleSelecting Media Type for Aquos Link Compatible Recorder Playback of Titles Using Aquos LinkManually Changing Aquos Audio Speaker System’s Sound Mode Hdmi Device SelectionAppendix Setting the TV on the WallRemoving the Stand Error message about reception of broadcast TroubleshootingTroubleshooting-Digital Broadcasting Problem Possible SolutionRS-232C Port Speciﬁcations Model LC-32E67U Optional AccessorySpeciﬁcations Part name Model numberInformation on the Software License for This Product PC Compatibility ChartClearing the Secret Number Calling for Service Limited WarrantyDimensional Drawings Sharp Electronics Corporation

Sharp LC-32E67U operation manual Other Viewing Options, Presetting Remote Control Function