Sharp LC-19A35X-BK, LC-19A35X-WH operation manual Energy conservation settings, Off 2 hr min hr min

Page 27

Watching TV

Energy conservation settings

Auto power-off at a designated time

Auto power-off after the end of broadcast

This function is conveniently used when, for instance, going to bed while watching TV.

1Press SLEEP.

Remaining time displays when sleep timer has been set.

Sleep timer: Remain 2 hr. 00 min.

2Each time you press SLEEP, the remaining time switches as shown below.

0 hr. 30 min.

 

1 hr. 00 min.

 

1 hr. 30 min.

 

 

Off 2 hr. 30 min. 2 hr. 00 min.

NOTE

When the time has been set, countdown automatically starts.

Five minutes before the preset of time expires, the remaining time displays each minute.

Select “Off” by pressing SLEEP to cancel the sleep timer.

You can set the TV to automatically power off in about 15 minutes after the TV goes into a state of receiving no programme signals, such as the end of a broadcast day.

1Press MENU and the MENU screen displays.

2Press c/d to select “Power Control”, and then press ENTER.

• Power control menu displays.

3Press a/b to select “No Signal Off”, and then press ENTER.

4Press a/b to select “Enable”, and then press

ENTER.

Five minutes before the power shuts down, the remaining time displays every minute.

NOTE

“Disable” is the factory preset value.

When a TV programme fi nishes, and the TV receives signal input, this function may not operate.

Auto power-off when there are no operations performed

You can set the TV to automatically power off when no TV operation is performed for more than 30 minutes or 3 hours.

1Press MENU and the MENU screen displays.

2Press c/d to select “Power Control”, and then press ENTER.

• Power control menu displays.

3Press a/b to select “No Operation Off”, and then press ENTER.

4Press a/b to select “30 min” or “3 hour”, and then press ENTER.

Five minutes before the power shuts down, the remaining time displays every minute.

NOTE

• “Disable” is the factory preset value.

25

Image 27
Contents LC-19A35X-BK LC-19A35X-WH Page Dear Sharp customer ContentsTeletext function Contents Watching TVSettings when using external devices Connecting a PCImportant Safety Precautions Trademarks Supplied accessoriesScrews g3 PreparationAttaching the stand Confi rm the 3 screws supplied with the TVPart names TV Front/SideTV/VIDEO button Volume display when headphones are plugged Preparation TV RearRegarding the headphone jack Preparation Remote control unit Bundling the cables Before turning on the powerConnecting the antenna cable Connecting the AC cordWhen using Hdmi cable Connecting external devicesConnecting a VCR, game console or camcorder Connecting a DVD playerPreparation Connecting a Digital TV STB Set Top Box You can use the Input 4 PC terminal when connecting to a PCDigital TV STB Set Top Box Inserting the batteries Using the remote control unitTurning the TV on/off Turning on the powerTurning off the power Power indicatorAbout Guide Display What is Menu? WUsing the control panel of the TVAbout Menu operations Basic Menu operationsDNR Press a/b to select Yes, and then press Setting channels automaticallyIf you have already set the password, enter it here Watching TVSelecting programmes Menu language settingsColour system See Sound system See Setting channels to your preferenceManual setting for each channel Auto searchColour system Watching TV Manual setting for each channelSearch tuning Fine tuningPress a/b to select Sort, and then press Sorting programmesSkipping channels Press a/b to select Skip, and then pressErase programme menus Watching TV Erasing programmesLabelling programmes Press a/b to select Label, and then pressOutputting only audio Using Mute e on the remote control unitUseful viewing functions Freezing the imageNicam TV broadcasts When receiving a stereo signal Watching TV Switching the analogue audio formatTV mode of A2 TV broadcasts When receiving a stereo signal When receiving a bilingual signalEnter the same 4-digit number as in to confi rm Setting a passwordSetting a channel Resetting the passwordEnergy conservation settings Auto power-off when there are no operations performedOff 2 hr min hr min Watching TV Power Management Mode1Mode2 Picture size settings WSS signal 43 screen Mode PanoramaPress a/b to select On or Off, and then press Enter Auto Selection Mode menuWatching TV Selecting the picture size manually Manual SelectionHdmi input mode Selecting a preset AV ModeUsing AV Mode on the remote control unit Press AV ModeManual picture settings Picture adjustmentOPC indicator P Setting Watching TV Advanced picture settingsColour Temp. Colour Temperature Film ModeRotating the image Other picture settingsAdjusting the image position DNR Digital Noise ReductionAudio adjustment WSound WidePress Menu to exit Press a/b to select the desired item, and then press Enter Settings when using external devicesSettings when using Hdmi output devices Connecting an Hdmi output deviceLabelling input sources Using TV/VIDEO on the remote control unit or on the TVUsing PC on the remote control unit Selecting input sourceFactory preset value is Auto Colour system settingsUse the PC terminals to connect a PC Connecting a PCSignal names for 15-pin mini D-sub connector Displaying a PC image on the screenNormal Full Dot by Dot Connecting a PC Selecting the picture sizeYou can select the picture size as illustrated below Press Wide or a/b to select a desired item on the menuConnecting a PC Adjusting the PC image automatically PhaseClock Selecting the input resolution Input resolution settings? ? ? Communication procedurePC Control of the TV Communication conditionsCommands PC compatibility chartRS-232C commands list Resolution Horizontal VerticalAbout Teletext Teletext functionDisplaying Subpages Displaying SubtitlesTeletext language setting Troubleshooting Problem Possible SolutionAppendix Press a/b to select Yes and then press ResetModel LC-19A35X SpecificationsDimensional drawings Password is Clearing the PasswordMemo Memo