Pelco c1943m operation manual Regulatory Notices, Product Warranty and Return Information

Page 20

REGULATORY NOTICES

NOTE: This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equip- ment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio commu- nications. However there is no guarantee that the interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television recep- tion, which can be determined by turning the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and the receiver.

Connect the equipment into an outlet on a circuit different from that to which the re- ceiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

PRODUCT WARRANTY AND RETURN INFORMATION

WARRANTY

Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment.

Exceptions to this warranty are as noted below:

Five years on FT/FR8000 Series fiber optic products.

Three years on Genex® Series products (multiplexers, server, and keyboard).

Three years on Camclosure® and fixed camera models, except the CC3701H-2, CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and MC3651H-2X camera models, which have a five-year warranty.

Two years on standard motorized or fixed focal length lenses.

Two years on Legacy®, CM6700/CM6800/CM9700 Series matrix, and DF5/DF8 Series fixed dome products.

Two years on Spectra®, Esprit®, ExSite, and PS20 scanners, including when used in continuous motion applications.

Two years on Esprit® and WW5700 Series window wiper (excluding wiper blades).

Eighteen months on DX Series digital video recorders, NVR300 Series network video recorders, and EnduraSeries distributed network-based video products.

One year (except video heads) on video cassette recorders (VCRs). Video heads will be covered for a period of six months.

Six months on all pan and tilts, scanners or preset lenses used in continuous motion applications (that is, preset scan, tour and auto scan modes).

Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco shipment. All goods requiring warranty repair shall be sent freight prepaid to Pelco, Clovis, California. Repairs made necessary by reason of misuse, alteration, normal wear, or accident are not covered under this warranty.

Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the specific use or application made of the Products. Pelco’s liability for any claim, whether based on breach of contract, negligence, infringement of any rights of any party or product liability, relating to the Products shall not exceed the price paid by the Dealer to Pelco for such Products. In no event will Pelco be liable for any special, incidental or consequential damages (including loss of use, loss of profit and claims of third parties) however caused, whether by the negligence of Pelco or otherwise.

The above warranty provides the Dealer with specific legal rights. The Dealer may also have additional rights, which are subject to variation from state to state.

If a warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or

(559)292-1981 to obtain a Repair Authorization number (RA), and provide the following information:

1.Model and serial number

2.Date of shipment, P.O. number, Sales Order number, or Pelco invoice number

3.Details of the defect or problem

If there is a dispute regarding the warranty of a product which does not fall under the warranty conditions stated above, please include a written explanation with the product when returned.

Method of return shipment shall be the same or equal to the method by which the item was received by Pelco.

RETURNS

In order to expedite parts returned to the factory for repair or credit, please call the factory at

(800)289-9100 or (559) 292-1981 to obtain an authorization number (CA number if returned for credit, and RA number if returned for repair).

All merchandise returned for credit may be subject to a 20% restocking and refurbishing charge.

Goods returned for repair or credit should be clearly identified with the assigned CA or RA number and freight should be prepaid. Ship to the appropriate address below.

If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico, send goods to:

Service Department

Pelco

3500 Pelco Way

Clovis, CA 93612-5699

If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and are instructed to return goods to the USA, you may do one of the following:

If the goods are to be sent by a COURIER SERVICE, send the goods to:

Pelco

3500 Pelco Way

Clovis, CA 93612-5699 USA

If the goods are to be sent by a FREIGHT FORWARDER, send the goods to:

Pelco c/o Expeditors 473 Eccles Avenue

South San Francisco, CA 94080 USA Phone: 650-737-1700

Fax: 650-737-0933

REVISION HISTORY

Manual #

Date

Comments

 

C1943M

9/99

Original version.

 

Pelco, the Pelco logo, Camclosure, Esprit, Genex, Legacy, System 9760, and Spectra are registered trademarks of Pelco.

© Copyright 1999, Pelco.

Endura and ExSite are trademarks of Pelco.

All rights reserved.

20

Pelco Manual C1943M (9/99)

Image 20
Contents CM9760-VCRC-P Contents Important Safeguards and Warnings DescriptionPRE-INSTALLATION Information ModelsOptions Front ViewDIP Switches LEDsRear View Rear View of CM9760-VCRC-PInput VCR Connectors VCR Input PlugsRelay Output Connector Communication ConnectorsDB-9 Connector Pin-outs Power Connections Power Input Fuse ReplacementSetup Preliminary Discussion DIP Switch SettingsDIP Switch Functions Configuring MGR Camera File for VCRC-P Operation Configuring the GPI Setup file for VCRC-P Operation Configuring the Comms file for VCRC-P Operation Installation Direct RACK-MOUNT HOOK-UPRemote Operation DAISY-CHAININGFunctional Block Diagram Operational OverviewOperating the CM9760-VCRC-P from the CM9760-KBD CM9760-KBD VCR Control FunctionsSpecifications ElectricalProduct Warranty and Return Information Regulatory Notices