Eiki LC-NB4S To change the code of Projector, To change the code of the Remote Control Unit

Page 36

SETTING

Power management

This function turns Projection Lamp off when this projector detects signal interruption and is not used for a certain period in order to reduce power consumption and maintain the Lamp-life. (This projector is shipped with this function ON.)

Power Management function operates to turn Projection Lamp off when the input signal is interrupted and any button is not pressed over 5 minutes. This function operates as follows;

1.When any input signal is interrupted, “No signal” and the counting down display appears (for 5 minutes).

2.After counting down for 5 minutes, Projection Lamp and READY Indicator are turned off. (Cooling Fans keep running.)

3.READY Indicator starts to flash after cooling down Projection Lamp about for 90 seconds (Power Management mode).

In this Power Management mode, Projection Lamp is automatically turned on when the input signal is connected or projector is operated with any button on Top Control or on Remote Control Unit again.

On start

When this function is “On,” projector is automatically turned on just by connecting AC Power cord to a wall outlet.

Note ; Be sure to turn projector off properly (refer to the section “TURNING OFF PROJECTOR” on P19). If projector is turned off in the wrong steps, On Start function does not operate properly.

Remote control

This projector has two different remote control codes; the factory-set normal code (Code 1) and the secondary code (Code 2). This switching function prevents remote control operation mixture (jam) when operating several projectors or video equipment together.

When operating projector in “Code 2,” both projector and Remote Control Unit must be switched to “Code 2.”

To change the code of Projector;

Set Remote control in the SETTING MENU to “Code 2.”

To change the code of the Remote Control Unit;

Press both MENU and IMAGE buttons on Remote Control Unit together for over 10 seconds.

After changing the code, make sure Remote Control Unit operates properly.

To return to the normal code (Code 1), operate both projector and Remote Control Unit in the ways above again.

NOTE : When batteries of Remote Control Unit are replaced or ALL- OFF switch is turned to “ALL-OFF,” the remote transmit code automatically returns to the normal code (Code 1).

Lamp counter reset

This function is used to reset Lamp Replace Counter. When replacing Projection Lamp, reset Lamp Replace Counter by using this function. Refer to page 38 for operation.

Time left until Lamp off.

Press SELECT button at this icon to display other items.

Press SELECT button at this icon to display previous items.

Move the pointer to the item and then press POINT LEFT/RIGHT button(s).

36

Image 36
Contents Model LC-NB4S To the Owner Safety Instructions Voor de klanten in NederlandCompliances Federal Communication Commission NoticeTable of Contents Features and Design Compact Design Digital Zoom for ComputerPreparation Name of Each Part of ProjectorHOT AIR Exhausted SETTING-UP Projector Connecting AC Power CordFor Continental Europe Adjustable Feet Preparation Positioning ProjectorRoom Light Preparation Moving Projector Connecting Projector Terminals of ProjectorVideo Input Jack Terminal Input JackConnecting to Computer Connecting ProjectorTerminals Projector Connecting to Video Equipment TerminalsOperation of Remote Control Unit Before OperationRemote Control Batteries Installation TOP Controls and Indicators Lamp Replace IndicatorHOW to Operate ON-SCREEN Menu Operating ON-SCREEN MenuFlow of ON-SCREEN Menu Operation Before Operation Menu BAR Guide WindowSound Menu Basic Operation Turning on / OFF ProjectorTurning on Projector Turning OFF ProjectorAdjusting Screen Zoom AdjustmentKeystone Adjustment Picture Freeze FunctionSound Adjustment Timer FunctionBasic Operation No Show Function Direct OperationComputer Input Selecting Input SourceSelecting Computer System RGB AnalogComputer Input Compatible Computer Specifications ResolutionResolution FreqPC Adjustment Auto PC AdjustmentPC Adjust Menu Auto PC AdjComputer Input Manual PC Adjustment Display area Display area HFull screen Picture Image Adjustments Image Level Select DirectImage Level Select Menu Image 1~4Computer Input Image Level Adjustment Image Adjust MenuPicture Screen Adjustment Screen MenuVideo Input VideoVideo Component Video Signal Format Selecting Video SystemPAL / Secam / Ntsc / NTSC4.43 / PAL-M / PAL-N AV System Menu Video or S-VIDEOCinema Video Input Image Level Adjustment ColorTint SharpnessProvides image at a normal video aspect ratio of 4 Setting Setting MenuSetting Menu To change the code of the Remote Control Unit To change the code of ProjectorLamp Replacement AppendixLamp Replace Lamp Handling Precautions Appendix Lamp Replace CounterOperating Wireless Mouse InstallationOperating Wireless Mouse Maintenance AIR Filter Care and CleaningCleaning Projection Lens RecommendationTroubleshooting Remote Control Unit Wireless MouseDoes not work Function does notTechnical Specifications Appendix Configurations of Terminals Monitor OUT Terminal AnalogDVI-I Terminal DIGITAL/ANALOG Control Port Connector Optional PartsPOA-MCSRL POA-MCMACPage Page Key to better communications Canada