Eiki LC-NB4S owner manual Lamp Handling Precautions, Appendix Lamp Replace Counter

Page 38

APPENDIX

LAMP REPLACE COUNTER

Be sure to reset the Lamp Replace Counter after the Lamp Assembly is replaced. When the Lamp Replace Counter is reset, the LAMP REPLACE Indicator stops lighting.

1

Turn projector on, press MENU button and ON-SCREEN

 

MENU will appear. Press POINT LEFT/RIGHT button(s) to

 

move a red frame pointer to SETTING Menu icon (refer to

 

page 35, 36).

2

Press POINT DOWN button to move a red frame pointer to

 

“Lamp counter reset” and then press SELECT button. The

 

message "Lamp replace counter reset?" is displayed. Move

 

the pointer to [Yes] and then press SELECT button.

3

Another confirmation dialog box appears and select [Yes] to

reset Lamp Replace Counter.

Move the pointer to Lamp counter reset and then press SELECT button. The message “Lamp replace counter reset?” is displayed.

NOTE : Do not reset the Lamp Replace Counter until after the Projection Lamp is replaced.

LAMP HANDLING PRECAUTIONS

This projector uses a high-pressure lamp which must be handled carefully and properly. Improper handling may result in accidents, injury, or create a fire hazard.

Lamp lifetime may differ from lamp to lamp and according to the environment of use. There is no guarantee of the same lifetime for each lamp. Some lamps may fail or terminate their lifetime in a shorter period of time than other similar lamps.

If the projector indicates that the lamp should be replaced, i.e., if the LAMP REPLACE INDICATOR lights up, replace the lamp with a new one IMMEDIATELY after the projector has cooled down.

( Follow carefully the instructions in the LAMP REPLACEMENT section of this manual. ) Continuous use of the lamp with the LAMP REPLACE INDICATOR lighted may increase the risk of lamp explosion.

A Lamp may explode as a result of vibration, shock or degradation as a result of hours of use as its lifetime draws to an end. Risk of explosion may differ according to the environment or conditions in which the projector and lamp are being used.

IF A LAMP EXPLODES, THE FOLLOWING SAFETY PRECAUTIONS SHOULD BE TAKEN.

If a lamp explodes, disconnect the projector’s AC plug from the AC outlet immediately. Contact an authorized service station for a checkup of the unit and replacement of the lamp. Additionally, check carefully to ensure that there are no broken shards or pieces of glass around the projector or coming out from the cooling air circulation holes. Any broken shards found should be cleaned up carefully. No one should check the inside of the projector except those who are authorized trained technicians and who are familiar with projector service. Inappropriate attempts to service the unit by anyone, especially those who are not appropriately trained to do so, may result in an accident or injury caused by pieces of broken glass.

38

Image 38
Contents Model LC-NB4S To the Owner Safety Instructions Voor de klanten in NederlandCompliances Federal Communication Commission NoticeTable of Contents Features and Design Compact Design Digital Zoom for ComputerHOT AIR Exhausted PreparationName of Each Part of Projector For Continental Europe SETTING-UP ProjectorConnecting AC Power Cord Room Light Adjustable FeetPreparation Positioning Projector Preparation Moving Projector Video Input Jack Connecting ProjectorTerminals of Projector Terminal Input JackTerminals Projector Connecting to ComputerConnecting Projector Connecting to Video Equipment TerminalsOperation of Remote Control Unit Before OperationRemote Control Batteries Installation TOP Controls and Indicators Lamp Replace IndicatorFlow of ON-SCREEN Menu Operation HOW to Operate ON-SCREEN MenuOperating ON-SCREEN Menu Sound Menu Before Operation Menu BARGuide Window Turning on Projector Basic OperationTurning on / OFF Projector Turning OFF ProjectorKeystone Adjustment Adjusting ScreenZoom Adjustment Picture Freeze FunctionBasic Operation No Show Function Sound AdjustmentTimer Function Direct OperationSelecting Computer System Computer InputSelecting Input Source RGB AnalogResolution Computer Input Compatible Computer SpecificationsResolution FreqPC Adjust Menu PC AdjustmentAuto PC Adjustment Auto PC AdjComputer Input Manual PC Adjustment Full screen Display areaDisplay area H Image Level Select Menu Picture Image AdjustmentsImage Level Select Direct Image 1~4Computer Input Image Level Adjustment Image Adjust MenuPicture Screen Adjustment Screen MenuVideo Video InputVideo PAL / Secam / Ntsc / NTSC4.43 / PAL-M / PAL-N Component Video Signal FormatSelecting Video System AV System Menu Video or S-VIDEOCinema Tint Video Input Image Level AdjustmentColor SharpnessProvides image at a normal video aspect ratio of 4 Setting Menu SettingSetting Menu To change the code of the Remote Control Unit To change the code of ProjectorLamp Replace Lamp ReplacementAppendix Lamp Handling Precautions Appendix Lamp Replace CounterOperating Wireless Mouse Operating Wireless MouseInstallation Cleaning Projection Lens MaintenanceAIR Filter Care and Cleaning RecommendationTroubleshooting Does not work Remote Control UnitWireless Mouse Function does notTechnical Specifications DVI-I Terminal DIGITAL/ANALOG Appendix Configurations of TerminalsMonitor OUT Terminal Analog POA-MCSRL Control Port ConnectorOptional Parts POA-MCMACPage Page Key to better communications Canada