Eiki LC-X71L owner manual Lamp Replacement

Page 48

APPENDIX

LAMP REPLACEMENT

When the projection lamp of this projector reaches its end of life, the LAMP REPLACE indicator lights yellow. If

this indicator lights yellow, replace the projection lamp

TOP CONTROL

 

with a new one promptly.

 

This indicator lights yellow

 

when the projection lamp

 

reaches its end of life.

 

Replace the projection lamp

 

with a new one promptly.

 

CAUTION

Allow the projector to cool for at least 45 minutes before you open the lamp cover. The inside of the projector can become very hot.

CAUTION

For continued safety, replace with a lamp assembly of the same type.

Do not drop the lamp assembly or touch a glass bulb! The glass can shatter and may cause injury.

Follow these steps to replace lamp assembly.

1

Turn off the projector and unplug the AC power cord.

 

Allow the projector to cool for at least 45 minutes.

2

Loosen the two (2) screws with a screwdriver and open

 

the lamp cover.

3

Loosen the two (2) screws with a screwdriver and pull out

 

the lamp assembly by using the built in handle.

4

Replace the lamp assembly with a new one and tighten

 

the two (2) screws. Make sure that the lamp assembly is

 

set properly. Put back the lamp cover and tighten the two

 

(2) screws.

5

Connect the AC power cord to the projector and turn on

 

the projector.

6

Reset the Lamp replacement counter (refer to”LAMP

 

REPLACE COUNTER” on the next page).

NOTE:

•Do not reset the Lamp replacement counter when the projection lamp is not replaced.

 

LAMP COVER

LAMP

HANDLE

ASSEMBLY

 

ORDER REPLACEMENT LAMP

Replacement lamp can be ordered through your dealer. When ordering a projection lamp, give the following information to the dealer.

●

Model No. of your projector

:

LC-X71/LC-X71L

●

Replacement Lamp Type No.

:

POA-LMP101

 

 

 

(Service Parts No. 610 328 7362)

48

Page 47 Page 49
Image 48
Page 47 Page 49
Contents LC-X71L Lensless To the Owner Risk of Electric Shock Do not OpenSafety Instructions Voor de klanten in NederlandAC Power Cord Requirement ComplianceEsperanza Rancho Santa Margarita CA 92688-2132, U.S.A Table of Contents Features and Design ComputersColor Systems Component VideoPreparation Name of Each Part of ProjectorSETTING-UP Projector Connecting AC Power Cord200 240 V AC Lens Installation Preparation Positioning ProjectorScreen 100 150 200 250 300 400 SizePreparation Adjustable Feet Installing Projector in Proper PositionPreparation Moving Projector Connecting Projector Terminals of ProjectorConnecting to Computers External Speaker TerminalsFront of the projector Terminals ProjectorConnecting to Video Equipment BNC Cable Scart Cable Video Cable Audio Cable RCA xTerminals Remote Control Operation Before OperationLaser Pointer Function Remote Control Batteries Installation Before OperationTOP Controls and Indicators EXT. SP SwitchLamp Replace Indicator Lamp IndicatorHOW to Operate ON-SCREEN Menu ON-SCREEN MenuFlow of ON-SCREEN Menu Operation Before Operation Menu BAR What is PIN code? Basic OperationTurning on / OFF Projector Turning on the ProjectorBasic Operation Turning OFF the Projector Adjusting Screen Focus AdjustmentLens Shift Adjustment Keystone CorrectionSound Adjustment Timer FunctionBasic Operation Picture Freeze Function No Show FunctionComputer Input Selecting Input SourceRGB AV Hdcp Input MenuSelecting Computer System Automatic MULTI-SCAN SystemPC System Menu SvgaPC Adjustment Auto PC AdjustmentPointer to the PC Adjust Menu icon PC Adjust MenuComputer Input Manual PC Adjustment Reset Mode freeStore QuitPicture Image Select Image Level SelectImage Select Menu Picture Screen Adjustment Picture Screen SelectScreen Menu Video Input Component Video Signal Format Selecting Video SystemPAL / Secam / Ntsc / NTSC4.43 / PAL-M / PAL-N AV System Menu Video or S-VIDEOPicture level adjusted for picture with fine tone CinemaImage button Standard Cinema Provides image at the normal video aspect ratio Provides image at the wide screen ratioPicture Image Adjustments Image Adjust MenuPointer Mode Picture ImageColor M MenuColor Palette DELWhite balance Red White balance GreenWhite balance Blue SharpnessSetting Setting MenuSetting Menu Language Logo Logo selectCapture Logo PIN code lockPower management CeilingRear AnamorphicRemote control To change the code of the remote controlOn start Lamp controlWireless Mouse mode Projector modeUSB Not usedTo Change the PIN Code Lock setting Changing the PIN code lock settingPIN code lock To Change the PIN Code PIN code lockLamp counter Factory default Exit the Setting MenuQuit Wireless Mouse AppendixLeft Click button Right Click buttonMaintenance Appendix AIR Filters Care and Cleaning Cleaning Projection LensLamp Replacement Appendix Lamp Replace Counter Turn the projector on and press the Menu button to displayLamp counter Troubleshooting Remote control Check the remote control code in the remote controlSeeSETTING on Check the mouse setting on your computerPC Adjust Menu TreeSystem Image Select ScreenSetting Image AdjustImage Select SoundAppendix Compatible Computer Specifications ResolutionIndicators and Projector Condition Ready indicator lights green AC power cord and contact the dealer or the serviceProjector is in the Power management mode Temperature inside the projector is abnormally highTechnical Specifications Projection Image Size DiagonalAppendix Configurations of Terminals Terminal HDB15-PIN Pin ConfigurationTerminal DVI 24-pin Pin Configuration Terminal Mini DIN 8-PIN Pin ConfigurationLens Replacement To the sales and service engineerAppendix Optional Parts PJ Link NoticeAppendix PIN Code Number Memo Logo PIN Code Lock NoDimensions Key to better communications Canada

LC-X71, LC-X71L specifications

The Eiki LC-X71L and LC-X71 are high-performance LCD projectors designed to meet the diverse needs of modern presentations and entertainment. Both models are built with exceptional technology and numerous features that enhance their usability in various environments, from boardrooms to classrooms.

At the heart of the Eiki LC-X71L and LC-X71 projectors is their advanced LCD technology, which ensures vibrant color reproduction and sharp image quality. With a native resolution of XGA (1024x768 pixels), these projectors deliver crisp visuals, making them ideal for detailed presentations and video playback. The high brightness levels, typically around 5000 lumens, ensure excellent visibility even in well-lit spaces, making it easier for audiences to see the content without strain.

One of the standout features of the Eiki LC-X71L and LC-X71 is their robust connectivity options. Both models are equipped with multiple input terminals, including HDMI, VGA, and composite video, allowing users to connect a variety of devices ranging from computers to gaming consoles. Moreover, the projectors support various input sources, such as USB and even wireless connectivity via optional adapters, promoting flexibility in presentation setups.

The Eiki LC-X71L and LC-X71 are also designed with user-friendliness in mind. The intuitive on-screen menu and straightforward remote control simplify navigation and operation, allowing users to adjust settings quickly. The projectors include features such as auto keystone correction, which automatically adjusts the image for optimal alignment, reducing setup time and improving productivity.

In terms of durability, both models feature a long lamp life, often exceeding 5000 hours in eco mode. This longevity enhances cost-effectiveness, minimizing the need for frequent lamp replacements and contributing to lower total ownership costs. Additionally, both projectors have efficient cooling systems to maintain optimal performance and prolong operational life.

Overall, the Eiki LC-X71L and LC-X71 projectors combine advanced technology, user-friendly features, and robust performance to cater to various applications. Whether for business meetings, educational purposes, or casual viewing, these projectors provide an exceptional visual experience that meets the high demands of today’s users.
Top Page Image Contents