TechniSat Integrated IRDETO Serial Interface RS, PLL-Modulator, LNB power supply, KHz-Modulation

Page 43

Teletext filtering

in accordance with standard ETS 300 472

Entry teletext data

compliant to ITU-R BT.653-2; lines: 6-22 and 320-335

TV-SCART:

 

Output

CVBS with RGB, or only CVBS, or only S-VHS (switchable)

VCR-SCART::

 

Input

CVBS with RGB or S-VHS

Output

CVBS or S-VHS

Serial Interface RS 232:

 

Type

RS 232 bi-directional

Bitrate

Max. 115.2 Kbit/s

Connection

9-pin D-SUB connector, male

Function

Pre-programming and updating operational software

PLL-Modulator:

 

Output range

UHF channels 21 to 69

Antenna input

47….862 MHz

Input/output impedance

75 Ohm

Antenna output

47…862 MHz, including re-modulated UHF signal

Video system

PAL / SECAM

LNB power supply:

 

LNB power

Max. 400 mA, short circuit detected

LNB voltage vertical

<14.0 V no load, >11.5 V at 400 mA

LNB voltage horizontal

<20 V no load, >17.5 V at 400 mA

 

LNB switched off in Standby mode

22 kHz-Modulation:

22 kHz, amplitude 0.6 V +/- 0.2 V

Programme memory/ Satellite positions:

 

 

No. of programmes user list TV:

999 TV programmes

(F1 to F999)

No. of programmes user list Radio:

999 radio programmes

(r1 to r999)

Number of Programmesl:

 

 

Bouquet lists TV/Radio total of 2000 programmes possible in bouquet lists

Number of active satellite positions:

 

 

Max. 4 (DiSEqC 1.0, SAT POSITION/ SAT OPTION)

 

Total number of satellite position:

32

 

One home transponder is stored in memory for each of the 32 satellite positions. This trans- ponder facilitates automatic channel/programme search on each satellite position.

EPG Data:

 

EPG preview:

Maximum 7 days in advance

Memory capacity:

Programmable for a maximum of 50 programmes

Timer:

 

Events

Maximum 128 events, one year in advance

Remote Control System:

RC-5

Sub-system address

8 (SAT 1)

Modulation frequency

36 kHz

Infrared wavelength

950 nm

43

Image 43
Contents DigiBox Irdeto MONO1/MONO2 Remote controlContents Page Al antenna Important hints on Usage Please read this firstEquipment not in use Safety InstructionsConnecting a DVB receiver to a satellite installation Connection to a Television set External InstallationConnections Mains connectionSetting the UHF Output Channel Serial Interface RS Video Cassette Recorders VCRSuper VHS Video Cassette Recorders AmplifierBasic Settings InstallationOSD Language Country Audio/Video SettingsParental lock GMT Time Offset hrsScreen Format TV Subtitel Adjustments for the External UnitAdjusting the Switching Matrix and LNB Properties Switching DiSEqC on or offAdditional Settings Poor reception, digital reception not possible Operation Switching on and offProgramme Selection Selecting blocked programmes Adjusting sound volumeReception of scrambled encrypted Programmes Selecting a different languageAdditional Programme Information TV/Radio selectionReturn to previous programme selected Displaying Time and Programme InformationInterrupting EPG download Electronic Programme GuideEPG functions allow you to Entering EPG dataNext Now Display of current programme contentsPreview Preselect Programmes Activate VCR Timer modeEPG Functions EPG InformationEPG Survey EPG Search Programming the Timer Timer on VCR Changing the Basic ProgrammingAdding/Deleting Channels Deleting items from the Total List Sorting ChannelsAdding items to the User Channel List Deleting items from the User ListChange PIN Locking ChannelsProgramming the Electronic Programme Guide Page Programme Search Unblocking the parental lock for individual channelsPage Page Activate factory settings/change data channels Page Embedded Irdeto System ConfigurationTechnical Terms Modulation at 22 KHz Software updateLNB/LNC Low Noise Block converter ModeUniversal LNB TransponderTechnical Data Serial Interface RS LNB power supplyTimer Remote Control System RC-5Mains voltage Troubleshooting GuidePower supply Mains switch Power usage Problem Possible Cause SolutionHOT Using the programme/channel list Summary for everyday use Switching on and offVolume adjustment Using the up/down arrow keys