Loewe ConceptL26, ConceptL32 manual Operating additional equipment, Login and connect equipment

Page 29

Operating additional equipment

Login and connect equipment

You have logged in and connected all connected equipment in the initial instal- lation. If you want to connect other equipment or disconnect equipment, call the connection wizard.

MENU

Call up the TV menu

 

OK

Select “Connections”

OK

Select the submenu line

 

OK

Select “New devices/modifications” and ...

OK

Call with OK.

State what equipment you want to connect. State whether a piece of audio equipment is to be connected (more details as of page 31). The connection wiz- ard then shows you which sockets you should connect this equipment to. Then connect the equipment to these sockets according to the connection diagram.

Connecting video/DVD recorders

In addition to the connection via the Euro-AV sockets, you also have to connect the antenna (only for terrestrial antenna or cable systems) through the VCR/DVD recorder to the TV set. The antenna signal is then available to the video/DVD recorder and the TV set.

Note: Use Euro-AV cables with right-angled plugs as shown.

ANT AV1

 

 

 

ENTREE

EURO AV2

 

 

ANTENNE

 

 

 

DECODER

 

 

 

 

AUDIO

AERIAL

 

SORTIE

OUT

EURO AV1

G

L

SORTIE

 

 

AUDIO/

 

 

ANTENNE

VIDEO

D

R

 

RF OUT

Search for and store the station of the video recorder (if no Euro-AV cable is available)

Switch on the test station on the VCR or insert a recorded tape and start play- back. In some video recorders the station must be switched on by activating the modulator.

Then call the AV selection on the TV set with 0 AV. Select the menu item “VIDEO” in the AV selection and call using OK.

To prevent “normal” TV stations being found in the search, pull out the antenna plug from the antenna input of the VCR temporarily (the cable to the antenna system).

If you cannot see the test station or playback from the cassette, the VCR is transmitting on a different channel. You then have to search for the station or set it manually.

1.Call the TV menu with the MENU button.

2.Select the “Settings” menu item with 34.

3.Select the line below using 6 and use 34 to select “Stations”.

4.Select the line below using 6and select “Manual adjustment” using 34 and call this menu using OK.

5.Enter channel “E30“ under the “Channel“ menu item (“Antenna/cable (analogue)”, select in this menu above if necessary).

6.Start search with the blue coloured key.

7.When the station has been found, change the name if needed, confirm with

OK and save with the red coloured key.

8.A list of the stored stations is displayed.

9.Select 0 (VIDEO) here and overwrite this station storage location using the red coloured key.

10.Hide the menu again using the END button.

Plug the antenna plug back in.

If you now get interference because a TV station is transmitting on the same channel as the VCR station, you have to change the transmitting station on the VCR and search for the VCR station on the TV again.

29 -

Page 28 Page 30
Image 29
Page 28 Page 30
Contents Operating instructions Contents Alternative Remote control Remote control TV functionsCall the menu Audio input left Video input AVS Control UnitCommon Interface 1 CI-Slot Connections to rear panelWelcome Disposal CleaningPacking and box SetTop of the TV. High levels of moisture For your safetyTop to ensure suf Is not exposed to directConnection First installationRemote control Handling the fabric hose optional Using the Conditional Access moduleSwitching on Station sorting Automatic programmingSelect a TV channel Switching on/offDirecting DVB-T antenna Changing stations Daily operationExample of the menu operation Basics about the menu operationFor the info system Info text indicates which settings you can make in StationsOK Use the OK button to call Switch off Automatic This is how to select the index itemFor the index DisplaysDirect control on TV set Setting the soundPicture settings Operating modes TV How the coloured keys work in TV modeShow status display Calling the indexCall additional functions Call timer overviewSelect picture format Move picture up/downDVB subtitles Under Settings you will find the following functionsRemoving the CA module Installing new DVB softwareInserting a new CA module Calling the CA module menuPicture in picture PIP Operating modes PIPSwitch to small PIP Setting the PIP typeSwitch to split screen Functions in the PIP menuOperating modes EPG Using the EPGEPG Programme guide To select within the menu lineProgramming recording for recorders Switch on TV when markedEPG menu Selecting providers and stations Analogue Teletext Operating modes Teletext Selection with the coloured keys Displaying teletext pagesDigital teletext operation only for MHEG-5 device versions Programme timer recordingsTeletext menu Radio Operating modes RadioRadio menu EPG Programme guideOperating additional equipment Login and connect equipmentConnecting video/DVD recorders Calling AV input via the station list Video playbackDevice to which the VCR is connected Now you will see the playback from the connected AV deviceAudio output Audio Digital OUT Assignment of digital audio inputs and outputsAudio input Audio Digital Six pin Cinch Cubic plug cable Only required for TV as centre loud speakerSound menu using the button, select Sound via and then TV Connecting other audio amplifiers or active speakersHdmi DVI connection Setting colour standardVGA/XGA connection Set geometrySound from PC or Set Top Box Component video connectionFunctions for Loewe video recorders VV 8106, 8136 Select the device to be operatedWhat to do, if Problem Possible cause RemedyDigital Link Plus does not function WiredReplace the Euro-AV cable That they fall between 1Type Concept L 26 Basic Concept L 32 Basic Technical dataGeneral data Connections Electrical dataAccessories Device version / Equipment Item no PIP tuner Digital Common Retrofitting optionsBasic 65434xxx 65442xxx MHEG-5Somara S.A Service
Top Page Image Contents