Panasonic NV-FJ610PMP manual Before Requesting Service, Message of On Screen Display

Page 39

Before Requesting Service

Before requesting service, check the following points again.

Message of On Screen Display

On screen display messages are displayed.

The error message is indicated in brackets [ ].

[PLEASE PUT IN A VIDEO CASSETTE.]

‘REC ¥ (¥ REC/OTR) or TIMER Á (TIMER REC Á) has been pressed without a video cassette inserted.

Insert a video cassette with an intact erasure prevention tab.

[PLEASE STOP THE TAPE.]

‘CHANNEL SET has been selected during playback. Stop the tape.

[PLEASE SET THE CLOCK.]

‘TIMER Á (TIMER REC Á) or PROG./ CHECK has been pressed when the clock is not set.

Set the clock.

[PLEASE USE A CASSETTE WITH TAB.]

‘REC ¥ (¥ REC/OTR) or TIMER Á (TIMER REC Á) has been pressed without a video cassette with an intact erasure prevention tab.

Use a video cassette with an intact erasure prevention tab.

[NO TIMER RECORDING HAS BEEN SET.]

‘TIMER Á (TIMER REC Á) has been pressed with no timer programs.

Set timer recording.

[VCR IS IN THE TIMER STANDBY MODE.]

‘POWER Í/I (POWER Í) has been pressed during the timer standby mode. Press TIMER Á (TIMER REC Á) to release the VCR from the timer standby mode.

Self-diagnostic Indications

This VCR has a self-diagnosis and display function. If the VCR detects trouble during installation or during use, the following indications automatically appear in the VCR display. Indications are in the form of a single English letter plus two numbers, such as [H01].

INDICATION: H∑∑, F∑∑

CAUSE: Some trouble has occurred. (Numbers after H and F differ according to the status of the VCR.)

REMEDY: Consult your dealer for further advice.

The VCR will not operate correctly

The symptom description is indicated in quatations “ ”.

“The VCR display is not illuminated.”

‘The AC power cord has not been connected.

Connect the AC power cord to the main AC power.

“The VCR display is illuminated but the VCR will not operate.”

‘The VCR is in the timer mode. Press TIMER Á (TIMER REC Á) to operate the VCR manually.

‘Safety devices are operating. Disconnect the AC power cord and wait for 1 minute. Reconnect the mains supply and check functions.

“An unknown language appears on the TV screen.”

‘The language setting has been set to an unknown language.

Select the desired language. See page 17.

Helpful Hints

39

Page 38 Page 40
Image 39
Page 38 Page 40
Contents NV-FJ610PMP NV-SJ410PMP NV-SJ410PMP CVC Crystal View Control IndicatorPlug in Auto Tuning Longrun Head SystemContents NV-FJ610PMP Controls and Connection SocketsBefore Use Infra-red Remote Controller DATE, ON, OFF PROG./CHECK Cancel Speed Timer ÁMenu OK Power Í Remote Controller Setup Power Source for the Remote ControllerPrecautions for Battery Replacement Basic Connections ConnectionsConnection to a TV using the Audio/Video Input Sockets Cable Connection Tuning the TV to your VCR Plug in Auto TuningTuning To Change the RF Output To Cancel Auto Tuning Mid- OperationTo Restart Plug in Auto Tuning Display SymbolStoring TV Broadcasts in your VCR PreparationsOn Screen Display Operations Channel Plan Manual System Setting ProcedurePreparation Setting the Remote Controller for Operation of your TVLanguage Setting of the On Screen Display To Select the Desired LanguageSelect Language Idioma by pressing 3 or 4 and then press OK Time Reset Function Setting the Clock of your VCRSettings Using the On Screen Display To Use the On Screen DisplayOn Screen Display By pressing 3 or Tape running display Stop, EjectInformation On Screen Display Select Tape SelectTo Select the Jet Search Speed in the EP mode For the Blue Background FunctionFor the Jet Navigator Function Audio Channel Selection NV-FJ610PMP only Auto Bilingual Choice Function NV-FJ610PMP onlySAP Select Direct REC by Select on or OFF byPressing 2 or ≥ Keep / D Pause PlaybackSlow Or / D PAUSE/SLOWOther Playback Functions To Stop Playback Automatically Playback Off Timer FunctionTo Play back the Recorded Part Repeatedly To Playback in the Desired Picture Quality Picture ModeTo Eject the Video Cassette Using the Remote Controller Mode Characteristic Example forPower Í/I Power Í Manual RecordingPress REC ¥ ¥ REC To Display the Approximate Remaining Tape Time To Select the Desired Tape SpeedTo Interrupt Recording To View One TV Program while Recording Another OneOne-Touch Recording OTR Direct RecordingPress Direct REC Set Starting time to Key ProgrammingExample Press PROG./ CheckSetting other Programs in Succession Weekly Timer RecordingDaily Timer Recording Timer Recording from an External Signal SourceChecking a Timer Program Cancelling a Timer ProgramJet Navigator list To cancel the Jet Navigator listSearch Functions Jet NavigatorCategory Indication Icon To Set the CategoryWhen Recording Over the Same Location on a Tape To Check the Recorded Programming Data Time Stamp FunctionTo Demonstrate the Jet Navigator Function To Find the Beginning Each Recording VHS Index Search System Recording Index SignalsPAUSE/SLOW again Assembly EditingEditing Recording VCROther Automatic Functions Other FunctionsVCR will not operate correctly Before Requesting ServiceMessage of On Screen Display Indication H∑∑, F∑∑Remote controller will not operate Correctly Playback will not operate correctlyRecording will not operate correctly Usage Precautions Avoid Sudden Changes in TemperatureHumidity and Dust Dirt on the video heads Small Large Normal AmountPicture Dirt Audio SpecificationsNV-FJ610PMP NV-SJ410PMP Video
Top Page Image Contents