Panasonic NV-HS880, NV-HS830 VCR Does Not Work Correctly, Playback Does Not Work Properly

Page 24

The VCR Does Not Work Correctly

[The VCR display is not illuminated.]

The AC mains lead is disconnected. Connect the AC mains lead securely.

VCR display setting is [OFF]. Set [VCR display] to [ON] or [DIMMED]. (See page 21.)

Power save setting is [ON]. (See page 20.)

[The VCR display is illuminated, but the VCR cannot be operated.]

The VCR is in the timer recording standby mode. Press the [TIMER] (20) to cancel the standby mode.

Safety devices are operating.

Disconnect the AC mains lead and wait approximately 1 minute before reconnecting.

Then check if the VCR can be operated.

[The VCR picture does not appear on the TV screen.]

The RF output channel is set to [ss].

Change the RF output channel to a channel other than [ss]. (See page 8.)

[Auto clock setting does not work correctly.]

Teletext information is not available or cannot be read. Set the clock manually.

[Download cannot be performed.]

The VCR is not connected to a TV equipped with the Q Link (or a similar) function via a fully-wired 21-pin Scart cable. Be sure to use a fully wired 21-pin Scart cable to connect the VCR to a TV with the Q Link (or a similar) function.

Playback Does Not Work Properly

[The playback picture is distorted or in black and white. Or, horizontal noise bars appear in the picture or horizontal lines move up and down.]

The tracking adjustment is not correct. Adjust the tracking. (See page 23.)

The TV’s video playback channel has not been tuned correctly. Re-tune the video playback channel.

The video heads are clogged or worn. Consult your dealer for advice.

The playback picture is distorted when using an E300 type video cassette that was recorded in the LP or EP mode.

We recommend that you use video cassettes other than type E300.

The playback picture is distorted when you record the tape in the EP mode using MESECAM system.

However, this is not a malfunction.

We recommend PAL system for recording in the EP mode.

During high speed cue and review playback (JET SEARCH), the tape transport noise will increase.

However, this is not a malfunction.

Recording Is Not Possible or Does Not Work Properly [When recording is attempted, the 1indication flashes.]

A video cassette with a broken out erasure prevention tab is used. Use a cassette with an intact tab, or if you want to erase the previously recorded contents on the cassette, cover the tab hole with two layers of adhesive tape.

[The playback picture of a recorded programme is distorted or no picture can be seen.]

The aerial or aerial lead connection is defective.

Check the connections. If the picture displayed on the TV is also distorted, there is something wrong with the installation of the aerial.

No programme was recorded because the VCR is not tuned correctly.

Tune it correctly.

No programme was recorded because the AV input was selected on the VCR.

Select the programme position of the desired TV programme.

[Timer recording does not work correctly.]

Time and date are not set or they are set incorrectly. Set the time and date correctly.

The starting time or ending time of the timer recording were not programmed correctly.

Set the starting time or ending time correctly.

The VCR was not put in the timer recording standby mode. After programming a timer recording, press the [TIMER] (20) to put the VCR in the timer recording standby mode.

[Recording from an external source connected to the VCR’s AV input cannot be made.]

The correct AV input is not selected. Select the correct AV input.

The connections from the external source are not made correctly. Correct them. (See page 11.)

The Remote Control Does Not Work Correctly

[The remote control does not work correctly.]

The remote control signal cannot reach the VCR.

Aim the remote control at the VCR and make sure that the infrared beam’s path is not obstructed.

The distance to the VCR is too long.

Use the remote control within 7 metres from the VCR. If you are using it within this range but the remote control still cannot operate the VCR, replace the batteries.

The batteries are exhausted. Replace with new batteries.

The batteries have been inserted with reversed polarities (+ and -).

Insert the batteries correctly. (See page 2.)

Power save setting is [ON]. (See page 20.)

The wrong remote control mode has been selected. Set the correct control mode. (See page 21.)

(For NV-HS880 Series)

24

Image 24
Contents Contents Video Cassette RecorderFor your safety Inserting Remote Control BatteriesMaintenance Conserve the environmentControls and Components Setting the Remote Control to Operate Your TV Menu OperationVCR Operation TV OperationConnecting and Setting up List of TVs Compatible with the VCR’s Remote ControlIf the TV cannot be operated properly Preset Download To Set Up this VCR with a TV Already in Use Auto Setup Function TV until the Country setting menu Using the VCR Press the OKTurn on the VCR and tune your To Stop Playback Automatically Playback Off Timer Function PlaybackTo Play back a Recorded Part Repeatedly To Prevent Accidental Erasure of Recorded Contents RecordingTo Select the Desired Tape Speed To Pause RecordingRecording from an external source CassetteRecording from an external source, for example from a video Satellite or Digital Receiver Cassette Recording Compatible PlaybackEquipment Connecting a Decoder Connecting a Stereo AmplifierLinked Timer Recordings by External Equipments EXT Link AV Link FunctionTimer Recording To Suspend the Timer Recording Standby ModeTo Programme with the On Screen Display OSD To Programme with the Showview FunctionSetting the Recording Date/Days To Check, Change or Cancel Timer Recording ProgrammingsTo Check the Total Timer Recording Programming Time Auto SP/LP Change FunctionIntelligent Timer Function Operation B When you want to edit the item of programmeDeleting the recording details Search Functions EditingManual Tuning Audio Dubbing For NV-HS880 SeriesTo Delete, Add or Move a Programme Position Setting the VCR’s Clock Various Settings To Manually Adjust the ClockTo Activate the Automatic Time Correction Function Language or Country Setting Other Function Crystal View Control Super CVC SuperChild Lock Function buttons Nicam Broadcasting System For NV-HS880EC and NV-HS830ECBefore Requesting Service Adjusting the Playback PictureConvenient Automatic Functions Remote Control Does Not Work Correctly VCR Does Not Work CorrectlyPlayback Does Not Work Properly Index 13, 19Specifications Video